Definition

Error messages for Windows XP Pro

TechTarget Contributor

MS Windows XP Professional Error Messages

Code	Error Message
0	The operation completed successfully.
1	Incorrect function.
2	The system cannot find the file specified.
3	The system cannot find the path specified.
4	The system cannot open the file.
5	Access is denied.
6	The handle is invalid.
7	The storage control blocks were destroyed.
8	Not enough storage is available to process this command.
9	The storage control block address is invalid.
10	The environment is incorrect.
11	An attempt was made to load a program with an incorrect format.
12	The access code is invalid.
13	The data is invalid.
14	Not enough storage is available to complete this operation.
15	The system cannot find the drive specified.
16	The directory cannot be removed.
17	The system cannot move the file to a different disk drive.
18	There are no more files.
19	The media is write protected.
20	The system cannot find the device specified.
21	The device is not ready.
22	The device does not recognize the command.
23	Data error (cyclic redundancy check).
24	The program issued a command but the command length is incorrect.
25	The drive cannot locate a specific area or track on the disk.
26	The specified disk or diskette cannot be accessed.
27	The drive cannot find the sector requested.
28	The printer is out of paper.
29	The system cannot write to the specified device.
30	The system cannot read from the specified device.
31	A device attached to the system is not functioning.
32	The process cannot access the file because it is being used by another process.
33	The process cannot access the file because another process has locked a portion of the file.
36	Too many files opened for sharing.
38	Reached the end of the file.
39	The disk is full.
50	The request is not supported.
51	Windows cannot find the network path. Verify that the network path is correct and the destination computer is not busy or turned off. If Windows still cannot find the network path, contact your network administrator.
52	You were not connected because a duplicate name exists on the network. Go to System in Control Panel to change the computer name and try again.
53	The network path was not found.
54	The network is busy.
55	The specified network resource or device is no longer available.
56	The network BIOS command limit has been reached.
57	A network adapter hardware error occurred.
58	The specified server cannot perform the requested operation.
59	An unexpected network error occurred.
60	The remote adapter is not compatible.
61	The printer queue is full.
62	Space to store the file waiting to be printed is not available on the server.
63	Your file waiting to be printed was deleted.
64	The specified network name is no longer available.
65	Network access is denied.
66	The network resource type is not correct.
67	The network name cannot be found.
68	The name limit for the local computer network adapter card was exceeded.
69	The network BIOS session limit was exceeded.
70	The remote server has been paused or is in the process of being started.
71	No more connections can be made to this remote computer at this time because there are already as many connections as the computer can accept.
72	The specified printer or disk device has been paused.
80	The file exists.
82	The directory or file cannot be created.
83	Fail on INT 24.
84	Storage to process this request is not available.
85	The local device name is already in use.
86	The specified network password is not correct.
87	The parameter is incorrect.
88	A write fault occurred on the network.
89	The system cannot start another process at this time.
100	Cannot create another system semaphore.
101	The exclusive semaphore is owned by another process.
102	The semaphore is set and cannot be closed.
103	The semaphore cannot be set again.
104	Cannot request exclusive semaphores at interrupt time.
105	The previous ownership of this semaphore has ended.
107	The program stopped because an alternate diskette was not inserted.
108	The disk is in use or locked by another process.
109	The pipe has been ended.
110	The system cannot open the device or file specified.
111	The file name is too long.
112	There is not enough space on the disk.
113	No more internal file identifiers available.
114	The target internal file identifier is incorrect.
117	The IOCTL call made by the application program is not correct.
118	The verify-on-write switch parameter value is not correct.
119	The system does not support the command requested.
120	This function is not supported on this system.
121	The semaphore timeout period has expired.
122	The data area passed to a system call is too small.
123	The filename, directory name, or volume label syntax is incorrect.
124	The system call level is not correct.
125	The disk has no volume label.
126	The specified module could not be found.
127	The specified procedure could not be found.
128	There are no child processes to wait for.
130	Attempt to use a file handle to an open disk partition for an operation other than raw disk I/O.
131	An attempt was made to move the file pointer before the beginning of the file.
132	The file pointer cannot be set on the specified device or file.
133	A JOIN or SUBST command cannot be used for a drive that contains previously joined drives.
134	An attempt was made to use a JOIN or SUBST command on a drive that has already been joined.
135	An attempt was made to use a JOIN or SUBST command on a drive that has already been substituted.
136	The system tried to delete the JOIN of a drive that is not joined.
137	The system tried to delete the substitution of a drive that is not substituted.
138	The system tried to join a drive to a directory on a joined drive.
139	The system tried to substitute a drive to a directory on a substituted drive.
140	The system tried to join a drive to a directory on a substituted drive.
141	The system tried to SUBST a drive to a directory on a joined drive.
142	The system cannot perform a JOIN or SUBST at this time.
143	The system cannot join or substitute a drive to or for a directory on the same drive.
144	The directory is not a subdirectory of the root directory.
145	The directory is not empty.
146	The path specified is being used in a substitute.
147	Not enough resources are available to process this command.
148	The path specified cannot be used at this time.
149	An attempt was made to join or substitute a drive for which a directory on the drive is the target of a previous substitute.
150	System trace information was not specified in your CONFIG.SYS file, or tracing is disallowed.
151	The number of specified semaphore events for DosMuxSemWait is not correct.
152	DosMuxSemWait did not execute; too many semaphores are already set.
153	The DosMuxSemWait list is not correct.
154	The volume label you entered exceeds the label character limit of the target file system.
155	Cannot create another thread.
156	The recipient process has refused the signal.
157	The segment is already discarded and cannot be locked.
158	The segment is already unlocked.
159	The address for the thread ID is not correct.
160	One or more arguments are not correct.
161	The specified path is invalid.
162	A signal is already pending.
164	No more threads can be created in the system.
167	Unable to lock a region of a file.
170	The requested resource is in use.
173	A lock request was not outstanding for the supplied cancel region.
174	The file system does not support atomic changes to the lock type.
180	The system detected a segment number that was not correct.
183	Cannot create a file when that file already exists.
186	The flag passed is not correct.
187	The specified system semaphore name was not found.
196	The operating system cannot run this application program.
197	The operating system is not presently configured to run this application.
199	The operating system cannot run this application program.
200	The code segment cannot be greater than or equal to 64K.
203	The system could not find the environment option that was entered.
205	No process in the command subtree has a signal handler.
206	The filename or extension is too long.
207	The ring 2 stack is in use.
208	The global filename characters, * or ?, are entered incorrectly or too many global filename characters are specified.
209	The signal being posted is not correct.
210	The signal handler cannot be set.
212	The segment is locked and cannot be reallocated.
214	Too many dynamic-link modules are attached to this program or dynamic-link module.
215	Cannot nest calls to LoadModule.
230	The pipe state is invalid.
231	All pipe instances are busy.
232	The pipe is being closed.
233	No process is on the other end of the pipe.
234	More data is available.
240	The session was canceled.
254	The specified extended attribute name was invalid.
255	The extended attributes are inconsistent.
258	The wait operation timed out.
259	No more data is available.
266	The copy functions cannot be used.
267	The directory name is invalid.
275	The extended attributes did not fit in the buffer.
276	The extended attribute file on the mounted file system is corrupt.
277	The extended attribute table file is full.
278	The specified extended attribute handle is invalid.
282	The mounted file system does not support extended attributes.
288	Attempt to release mutex not owned by caller.
298	Too many posts were made to a semaphore.
299	Only part of a ReadProcessMemory or WriteProcessMemory request was completed.
300	The oplock request is denied.
301	An invalid oplock acknowledgment was received by the system.
302	The volume is too fragmented to complete this operation.
303	The file cannot be opened because it is in the process of being deleted.
487	Attempt to access invalid address.
534	Arithmetic result exceeded 32 bits.
535	There is a process on other end of the pipe.
536	Waiting for a process to open the other end of the pipe.
994	Access to the extended attribute was denied.
995	The I/O operation has been aborted because of either a thread exit or an application request.
996	Overlapped I/O event is not in a signaled state.
997	Overlapped I/O operation is in progress.
998	Invalid access to memory location.
999	Error performing inpage operation.
1001	Recursion too deep; the stack overflowed.
1002	The window cannot act on the sent message.
1003	Cannot complete this function.
1004	Invalid flags.
1005	The volume does not contain a recognized file system. Please make sure that all required file system drivers are loaded and that the volume is not corrupted.
1006	The volume for a file has been externally altered so that the opened file is no longer valid.
1007	The requested operation cannot be performed in full-screen mode.
1008	An attempt was made to reference a token that does not exist.
1009	The configuration registry database is corrupt.
1010	The configuration registry key is invalid.
1011	The configuration registry key could not be opened.
1012	The configuration registry key could not be read.
1013	The configuration registry key could not be written.
1014	One of the files in the registry database had to be recovered by use of a log or alternate copy. The recovery was successful.
1015	The registry is corrupted. The structure of one of the files containing registry data is corrupted, or the system's memory image of the file is corrupted, or the file could not be recovered because the alternate copy or log was absent or corrupted.
1016	An I/O operation initiated by the registry failed unrecoverably. The registry could not read in, or write out, or flush, one of the files that contain the system's image of the registry.
1017	The system has attempted to load or restore a file into the registry, but the specified file is not in a registry file format.
1018	Illegal operation attempted on a registry key that has been marked for deletion.
1019	System could not allocate the required space in a registry log.
1020	Cannot create a symbolic link in a registry key that already has subkeys or values.
1021	Cannot create a stable subkey under a volatile parent key.
1022	A notify change request is being completed and the information is not being returned in the caller's buffer. The caller now needs to enumerate the files to find the changes.
1051	A stop control has been sent to a service that other running services are dependent on.
1052	The requested control is not valid for this service.
1053	The service did not respond to the start or control request in a timely fashion.
1054	A thread could not be created for the service.
1055	The service database is locked.
1056	An instance of the service is already running.
1057	The account name is invalid or does not exist, or the password is invalid for the account name specified.
1058	The service cannot be started, either because it is disabled or because it has no enabled devices associated with it.
1059	Circular service dependency was specified.
1060	The specified service does not exist as an installed service.
1061	The service cannot accept control messages at this time.
1062	The service has not been started.
1063	The service process could not connect to the service controller.
1064	An exception occurred in the service when handling the control request.
1065	The database specified does not exist.
1066	The service has returned a service-specific error code.
1067	The process terminated unexpectedly.
1068	The dependency service or group failed to start.
1069	The service did not start due to a logon failure.
1070	After starting, the service hung in a start-pending state.
1071	The specified service database lock is invalid.
1072	The specified service has been marked for deletion.
1073	The specified service already exists.
1074	The system is currently running with the last-known-good configuration.
1075	The dependency service does not exist or has been marked for deletion.
1076	The current boot has already been accepted for use as the last-known-good control set.
1077	No attempts to start the service have been made since the last boot.
1078	The name is already in use as either a service name or a service display name.
1079	The account specified for this service is different from the account specified for other services running in the same process.
1080	Failure actions can only be set for Win32 services, not for drivers.
1081	This service runs in the same process as the service control manager. Therefore, the service control manager cannot take action if this service's process terminates unexpectedly.
1082	No recovery program has been configured for this service.
1083	The executable program that this service is configured to run in does not implement the service.
1084	This service cannot be started in Safe Mode
1100	The physical end of the tape has been reached.
1101	A tape access reached a filemark.
1102	The beginning of the tape or a partition was encountered.
1103	A tape access reached the end of a set of files.
1104	No more data is on the tape.
1105	Tape could not be partitioned.
1106	When accessing a new tape of a multivolume partition, the current block size is incorrect.
1107	Tape partition information could not be found when loading a tape.
1108	Unable to lock the media eject mechanism.
1109	Unable to unload the media.
1110	The media in the drive may have changed.
1111	The I/O bus was reset.
1112	No media in drive.
1113	No mapping for the Unicode character exists in the target multi-byte code page.
1114	A dynamic link library (DLL) initialization routine failed.
1115	A system shutdown is in progress.
1116	Unable to abort the system shutdown because no shutdown was in progress.
1117	The request could not be performed because of an I/O device error.
1118	No serial device was successfully initialized. The serial driver will unload.
1119	Unable to open a device that was sharing an interrupt request (IRQ) with other devices. At least one other device that uses that IRQ was already opened.
1120	A serial I/O operation was completed by another write to the serial port. (The IOCTL_SERIAL_XOFF_COUNTER reached zero.)
1121	A serial I/O operation completed because the timeout period expired. (The IOCTL_SERIAL_XOFF_COUNTER did not reach zero.)
1122	No ID address mark was found on the floppy disk.
1123	Mismatch between the floppy disk sector ID field and the floppy disk controller track address.
1124	The floppy disk controller reported an error that is not recognized by the floppy disk driver.
1125	The floppy disk controller returned inconsistent results in its registers.
1126	While accessing the hard disk, a recalibrate operation failed, even after retries.
1127	While accessing the hard disk, a disk operation failed even after retries.
1128	While accessing the hard disk, a disk controller reset was needed, but even that failed.
1129	Physical end of tape encountered.
1130	Not enough server storage is available to process this command.
1131	A potential deadlock condition has been detected.
1132	The base address or the file offset specified does not have the proper alignment.
1140	An attempt to change the system power state was vetoed by another application or driver.
1141	The system BIOS failed an attempt to change the system power state.
1142	An attempt was made to create more links on a file than the file system supports.
1150	The specified program requires a newer version of Windows.
1151	The specified program is not a Windows or MS-DOS program.
1152	Cannot start more than one instance of the specified program.
1153	The specified program was written for an earlier version of Windows.
1154	One of the library files needed to run this application is damaged.
1155	No application is associated with the specified file for this operation.
1156	An error occurred in sending the command to the application.
1157	One of the library files needed to run this application cannot be found.
1158	The current process has used all of its system allowance of handles for Window Manager objects.
1159	The message can be used only with synchronous operations.
1160	The indicated source element has no media.
1161	The indicated destination element already contains media.
1162	The indicated element does not exist.
1163	The indicated element is part of a magazine that is not present.
1164	The indicated device requires reinitialization due to hardware errors.
1165	The device has indicated that cleaning is required before further operations are attempted.
1166	The device has indicated that its door is open.
1167	The device is not connected.
1168	Element not found.
1169	There was no match for the specified key in the index.
1170	The property set specified does not exist on the object.
1171	The point passed to GetMouseMovePoints is not in the buffer.
1172	The tracking (workstation) service is not running.
1173	The Volume ID could not be found.
1175	Unable to remove the file to be replaced.
1176	Unable to move the replacement file to the file to be replaced. The file to be replaced has retained its original name.
1177	Unable to move the replacement file to the file to be replaced. The file to be replaced has been renamed using the backup name.
1178	The volume change journal is being deleted.
1179	The volume change journal is not active.
1180	A file was found, but it may not be the correct file.
1181	The journal entry has been deleted from the journal.
1200	The specified device name is invalid.
1201	The device is not currently connected but it is a remembered connection.
1202	The local device name has a remembered connection to another network resource.
1203	No network provider accepted the given network path.
1204	The specified network provider name is invalid.
1205	Unable to open the network connection profile.
1206	The network connection profile is corrupted.
1207	Cannot enumerate a noncontainer.
1208	An extended error has occurred.
1209	The format of the specified group name is invalid.
1210	The format of the specified computer name is invalid.
1211	The format of the specified event name is invalid.
1212	The format of the specified domain name is invalid.
1213	The format of the specified service name is invalid.
1214	The format of the specified network name is invalid.
1215	The format of the specified share name is invalid.
1216	The format of the specified password is invalid.
1217	The format of the specified message name is invalid.
1218	The format of the specified message destination is invalid.
1219	Multiple connections to a server or shared resource by the same user, using more than one user name, are not allowed. Disconnect all previous connections to the server or shared resource and try again..
1220	An attempt was made to establish a session to a network server, but there are already too many sessions established to that server.
1221	The workgroup or domain name is already in use by another computer on the network.
1222	The network is not present or not started.
1223	The operation was canceled by the user.
1224	The requested operation cannot be performed on a file with a user-mapped section open.
1225	The remote system refused the network connection.
1226	The network connection was gracefully closed.
1227	The network transport endpoint already has an address associated with it.
1228	An address has not yet been associated with the network endpoint.
1229	An operation was attempted on a nonexistent network connection.
1230	An invalid operation was attempted on an active network connection.
1231	The network location cannot be reached. For information about network troubleshooting, see Windows Help.
1232	The network location cannot be reached. For information about network troubleshooting, see Windows Help.
1233	The network location cannot be reached. For information about network troubleshooting, see Windows Help.
1234	No service is operating at the destination network endpoint on the remote system.
1235	The request was aborted.
1236	The network connection was aborted by the local system.
1237	The operation could not be completed. A retry should be performed.
1238	A connection to the server could not be made because the limit on the number of concurrent connections for this account has been reached.
1239	Attempting to log in during an unauthorized time of day for this account.
1240	The account is not authorized to log in from this station.
1241	The network address could not be used for the operation requested.
1242	The service is already registered.
1243	The specified service does not exist.
1244	The operation being requested was not performed because the user has not been authenticated.
1245	The operation being requested was not performed because the user has not logged on to the network. The specified service does not exist.
1246	Continue with work in progress.
1247	An attempt was made to perform an initialization operation when initialization has already been completed.
1248	No more local devices.
1249	The specified site does not exist.
1250	A domain controller with the specified name already exists.
1251	This operation is supported only when you are connected to the server.
1252	The group policy framework should call the extension even if there are no changes.
1253	The specified user does not have a valid profile.
1254	This operation is not supported on a Microsoft Small Business Server
1255	The server machine is shutting down.
1256	The remote system is not available. For information about network troubleshooting, see Windows Help.
1257	The security identifier provided is not from an account domain.
1258	The security identifier provided does not have a domain component.
1259	AppHelp dialog canceled thus preventing the application from starting.
1260	Windows cannot open this program because it has been prevented by a software restriction policy. For more information, open Event Viewer or contact your system administrator.
1261	A program attempt to use an invalid register value. Normally caused by an uninitialized register. This error is Itanium specific.
1262	The share is currently offline or does not exist.
1263	The kerberos protocol encountered an error while validating the KDC certificate during smartcard logon.
1264	The kerberos protocol encountered an error while attempting to utilize the smartcard subsystem.
1265	The system detected a possible attempt to compromise security. Please ensure that you can contact the server that authenticated you.
1266	The smartcard certificate used for authentication has been revoked. Please contact your system administrator. There may be additional information in the event log.
1267	An untrusted certificate authority was detected While processing the smartcard certificate used for authentication. Please contact your system administrator.
1268	The revocation status of the smartcard certificate used for authentication could not be determined. Please contact your system administrator.
1269	The smartcard certificate used for authentication was not trusted. Please contact your system administrator.
1270	The smartcard certificate used for authentication has expired. Please contact your system administrator.
1271	The machine is locked and can not be shut down without the force option.
1273	An application-defined callback gave invalid data when called.
1274	The group policy framework should call the extension in the synchronous foreground policy refresh.
1275	This driver has been blocked from loading
1276	A dynamic link library (DLL) referenced a module that was neither a DLL nor the process's executable image.
1300	Not all privileges referenced are assigned to the caller.
1301	Some mapping between account names and security IDs was not done.
1302	No system quota limits are specifically set for this account.
1303	No encryption key is available. A well-known encryption key was returned.
1304	The password is too complex to be converted to a LAN Manager password. The LAN Manager password returned is a NULL string.
1305	The revision level is unknown.
1306	Indicates two revision levels are incompatible.
1307	This security ID may not be assigned as the owner of this object.
1308	This security ID may not be assigned as the primary group of an object.
1309	An attempt has been made to operate on an impersonation token by a thread that is not currently impersonating a client.
1310	The group may not be disabled.
1311	There are currently no logon servers available to service the logon request.
1312	A specified logon session does not exist. It may already have been terminated.
1313	A specified privilege does not exist.
1314	A required privilege is not held by the client.
1315	The name provided is not a properly formed account name.
1316	The specified user already exists.
1317	The specified user does not exist.
1318	The specified group already exists.
1319	The specified group does not exist.
1320	Either the specified user account is already a member of the specified group, or the specified group cannot be deleted because it contains a member.
1321	The specified user account is not a member of the specified group account.
1322	The last remaining administration account cannot be disabled or deleted.
1323	Unable to update the password. The value provided as the current password is incorrect.
1324	Unable to update the password. The value provided for the new password contains values that are not allowed in passwords.
1325	Unable to update the password. The value provided for the new password does not meet the length, complexity, or history requirement of the domain.
1326	Logon failure: unknown user name or bad password.
1327	Logon failure: user account restriction. Possible reasons are blank passwords not allowed, logon hour restrictions, or a policy restriction has been enforced.
1328	Logon failure: account logon time restriction violation.
1329	Logon failure: user not allowed to log on to this computer.
1330	Logon failure: the specified account password has expired.
1331	Logon failure: account currently disabled.
1332	No mapping between account names and security IDs was done.
1333	Too many local user identifiers (LUIDs) were requested at one time.
1334	No more local user identifiers (LUIDs) are available.
1335	The subauthority part of a security ID is invalid for this particular use.
1336	The access control list (ACL) structure is invalid.
1337	The security ID structure is invalid.
1338	The security descriptor structure is invalid.
1340	The inherited access control list (ACL) or access control entry (ACE) could not be built.
1341	The server is currently disabled.
1342	The server is currently enabled.
1343	The value provided was an invalid value for an identifier authority.
1344	No more memory is available for security information updates.
1345	The specified attributes are invalid, or incompatible with the attributes for the group as a whole.
1346	Either a required impersonation level was not provided, or the provided impersonation level is invalid.
1347	Cannot open an anonymous level security token.
1348	The validation information class requested was invalid.
1349	The type of the token is inappropriate for its attempted use.
1350	Unable to perform a security operation on an object that has no associated security.
1351	Configuration information could not be read from the domain controller, either because the machine is unavailable, or access has been denied.
1352	The security account manager (SAM) or local security authority (LSA) server was in the wrong state to perform the security operation.
1353	The domain was in the wrong state to perform the security operation.
1354	This operation is only allowed for the Primary Domain Controller of the domain.
1355	The specified domain either does not exist or could not be contacted.
1356	The specified domain already exists.
1357	An attempt was made to exceed the limit on the number of domains per server.
1358	Unable to complete the requested operation because of either a catastrophic media failure or a data structure corruption on the disk.
1359	An internal error occurred.
1360	Generic access types were contained in an access mask which should already be mapped to nongeneric types.
1361	A security descriptor is not in the right format (absolute or self-relative).
1362	The requested action is restricted for use by logon processes only. The calling process has not registered as a logon process.
1363	Cannot start a new logon session with an ID that is already in use.
1364	A specified authentication package is unknown.
1365	The logon session is not in a state that is consistent with the requested operation.
1366	The logon session ID is already in use.
1367	A logon request contained an invalid logon type value.
1368	Unable to impersonate using a named pipe until data has been read from that pipe.
1369	The transaction state of a registry subtree is incompatible with the requested operation.
1370	An internal security database corruption has been encountered.
1371	Cannot perform this operation on built-in accounts.
1372	Cannot perform this operation on this built-in special group.
1373	Cannot perform this operation on this built-in special user.
1374	The user cannot be removed from a group because the group is currently the user's primary group.
1375	The token is already in use as a primary token.
1376	The specified local group does not exist.
1377	The specified account name is not a member of the local group.
1378	The specified account name is already a member of the local group.
1379	The specified local group already exists.
1380	Logon failure: the user has not been granted the requested logon type at this computer.
1381	The maximum number of secrets that may be stored in a single system has been exceeded.
1382	The length of a secret exceeds the maximum length allowed.
1383	The local security authority database contains an internal inconsistency.
1384	During a logon attempt, the user's security context accumulated too many security IDs.
1385	Logon failure: the user has not been granted the requested logon type at this computer.
1386	A cross-encrypted password is necessary to change a user password.
1387	A member could not be added to or removed from the local group because the member does not exist.
1388	A new member could not be added to a local group because the member has the wrong account type.
1389	Too many security IDs have been specified.
1390	A cross-encrypted password is necessary to change this user password.
1391	Indicates an ACL contains no inheritable components.
1392	The file or directory is corrupted and unreadable.
1393	The disk structure is corrupted and unreadable.
1394	There is no user session key for the specified logon session.
1395	The service being accessed is licensed for a particular number of connections. No more connections can be made to the service at this time because there are already as many connections as the service can accept.
1396	Logon Failure: The target account name is incorrect.
1397	Mutual Authentication failed. The server's password is out of date at the domain controller.
1398	There is a time and/or date difference between the client and server.
1399	This operation can not be performed on the current domain.
1400	Invalid window handle.
1401	Invalid menu handle.
1402	Invalid cursor handle.
1403	Invalid accelerator table handle.
1404	Invalid hook handle.
1405	Invalid handle to a multiple-window position structure.
1406	Cannot create a top-level child window.
1407	Cannot find window class.
1408	Invalid window; it belongs to other thread.
1409	Hot key is already registered.
1410	Class already exists.
1411	Class does not exist.
1412	Class still has open windows.
1413	Invalid index.
1414	Invalid icon handle.
1415	Using private DIALOG window words.
1416	The list box identifier was not found.
1417	No wildcards were found.
1418	Thread does not have a clipboard open.
1419	Hot key is not registered.
1420	The window is not a valid dialog window.
1421	Control ID not found.
1422	Invalid message for a combo box because it does not have an edit control.
1423	The window is not a combo box.
1424	Height must be less than 256.
1425	Invalid device context (DC) handle.
1426	Invalid hook procedure type.
1427	Invalid hook procedure.
1428	Cannot set nonlocal hook without a module handle.
1429	This hook procedure can only be set globally.
1430	The journal hook procedure is already installed.
1431	The hook procedure is not installed.
1432	Invalid message for single-selection list box.
1433	LB_SETCOUNT sent to non-lazy list box.
1434	This list box does not support tab stops.
1435	Cannot destroy object created by another thread.
1436	Child windows cannot have menus.
1437	The window does not have a system menu.
1438	Invalid message box style.
1439	Invalid system-wide (SPI_*) parameter.
1440	Screen already locked.
1441	All handles to windows in a multiple-window position structure must have the same parent.
1442	The window is not a child window.
1443	Invalid GW_* command.
1444	Invalid thread identifier.
1445	Cannot process a message from a window that is not a multiple document interface (MDI) window.
1446	Popup menu already active.
1447	The window does not have scroll bars.
1448	Scroll bar range cannot be greater than MAXLONG.
1449	Cannot show or remove the window in the way specified.
1450	Insufficient system resources exist to complete the requested service.
1451	Insufficient system resources exist to complete the requested service.
1452	Insufficient system resources exist to complete the requested service.
1453	Insufficient quota to complete the requested service.
1454	Insufficient quota to complete the requested service.
1455	The paging file is too small for this operation to complete.
1456	A menu item was not found.
1457	Invalid keyboard layout handle.
1458	Hook type not allowed.
1459	This operation requires an interactive window station.
1460	This operation returned because the timeout period expired.
1461	Invalid monitor handle.
1500	The event log file is corrupted.
1501	No event log file could be opened, so the event logging service did not start.
1502	The event log file is full.
1503	The event log file has changed between read operations.
1601	The Windows Installer Service could not be accessed. This can occur if you are running Windows in safe mode, or if the Windows Installer is not correctly installed. Contact your support personnel for assistance.
1602	User cancelled installation.
1603	Fatal error during installation.
1604	Installation suspended, incomplete.
1605	This action is only valid for products that are currently installed.
1606	Feature ID not registered.
1607	Component ID not registered.
1608	Unknown property.
1609	Handle is in an invalid state.
1610	The configuration data for this product is corrupt. Contact your support personnel.
1611	Component qualifier not present.
1612	The installation source for this product is not available. Verify that the source exists and that you can access it.
1613	This installation package cannot be installed by the Windows Installer service. You must install a Windows service pack that contains a newer version of the Windows Installer service.
1614	Product is uninstalled.
1615	SQL query syntax invalid or unsupported.
1616	Record field does not exist.
1617	The device has been removed.
1618	Another installation is already in progress. Complete that installation before proceeding with this install.
1619	This installation package could not be opened. Verify that the package exists and that you can access it, or contact the application vendor to verify that this is a valid Windows Installer package.
1620	This installation package could not be opened. Contact the application vendor to verify that this is a valid Windows Installer package.
1621	There was an error starting the Windows Installer service user interface. Contact your support personnel.
1622	Error opening installation log file. Verify that the specified log file location exists and that you can write to it.
1623	The language of this installation package is not supported by your system.
1624	Error applying transforms. Verify that the specified transform paths are valid.
1625	This installation is forbidden by system policy. Contact your system administrator.
1626	Function could not be executed.
1627	Function failed during execution.
1628	Invalid or unknown table specified.
1629	Data supplied is of wrong type.
1630	Data of this type is not supported.
1631	The Windows Installer service failed to start. Contact your support personnel.
1632	The Temp folder is on a drive that is full or is inaccessible. Free up space on the drive or verify that you have write permission on the Temp folder.
1633	This installation package is not supported by this processor type. Contact your product vendor.
1634	Component not used on this computer.
1635	This patch package could not be opened. Verify that the patch package exists and that you can access it, or contact the application vendor to verify that this is a valid Windows Installer patch package.
1636	This patch package could not be opened. Contact the application vendor to verify that this is a valid Windows Installer patch package.
1637	This patch package cannot be processed by the Windows Installer service. You must install a Windows service pack that contains a newer version of the Windows Installer service.
1638	Another version of this product is already installed. Installation of this version cannot continue. To configure or remove the existing version of this product, use Add/Remove Programs on the Control Panel.
1639	Invalid command line argument. Consult the Windows Installer SDK for detailed command line help.
1640	Only administrators have permission to add, remove, or configure server software during a Terminal services remote session. If you want to install or configure software on the server, contact your network administrator.
1641	The requested operation completed successfully. The system will be restarted so the changes can take effect.
1642	The upgrade patch cannot be installed by the Windows Installer service because the program to be upgraded may be missing, or the upgrade patch may update a different version of the program. Verify that the program to be upgraded exists on your computer an
1643	The patch package is not permitted by software restriction policy.
1644	One or more customizations are not permitted by software restriction policy.
1700	The string binding is invalid.
1701	The binding handle is not the correct type.
1702	The binding handle is invalid.
1703	The RPC protocol sequence is not supported.
1704	The RPC protocol sequence is invalid.
1705	The string universal unique identifier (UUID) is invalid.
1706	The endpoint format is invalid.
1707	The network address is invalid.
1708	No endpoint was found.
1709	The timeout value is invalid.
1710	The object universal unique identifier (UUID) was not found.
1711	The object universal unique identifier (UUID) has already been registered.
1712	The type universal unique identifier (UUID) has already been registered.
1713	The RPC server is already listening.
1714	No protocol sequences have been registered.
1715	The RPC server is not listening.
1716	The manager type is unknown.
1717	The interface is unknown.
1718	There are no bindings.
1719	There are no protocol sequences.
1720	The endpoint cannot be created.
1721	Not enough resources are available to complete this operation.
1722	The RPC server is unavailable.
1723	The RPC server is too busy to complete this operation.
1724	The network options are invalid.
1725	There are no remote procedure calls active on this thread.
1726	The remote procedure call failed.
1727	The remote procedure call failed and did not execute.
1728	A remote procedure call (RPC) protocol error occurred.
1730	The transfer syntax is not supported by the RPC server.
1732	The universal unique identifier (UUID) type is not supported.
1733	The tag is invalid.
1734	The array bounds are invalid.
1735	The binding does not contain an entry name.
1736	The name syntax is invalid.
1737	The name syntax is not supported.
1739	No network address is available to use to construct a universal unique identifier (UUID).
1740	The endpoint is a duplicate.
1741	The authentication type is unknown.
1742	The maximum number of calls is too small.
1743	The string is too long.
1744	The RPC protocol sequence was not found.
1745	The procedure number is out of range.
1746	The binding does not contain any authentication information.
1747	The authentication service is unknown.
1748	The authentication level is unknown.
1749	The security context is invalid.
1750	The authorization service is unknown.
1751	The entry is invalid.
1752	The server endpoint cannot perform the operation.
1753	There are no more endpoints available from the endpoint mapper.
1754	No interfaces have been exported.
1755	The entry name is incomplete.
1756	The version option is invalid.
1757	There are no more members.
1758	There is nothing to unexport.
1759	The interface was not found.
1760	The entry already exists.
1761	The entry is not found.
1762	The name service is unavailable.
1763	The network address family is invalid.
1764	The requested operation is not supported.
1765	No security context is available to allow impersonation.
1766	An internal error occurred in a remote procedure call (RPC).
1767	The RPC server attempted an integer division by zero.
1768	An addressing error occurred in the RPC server.
1769	A floating-point operation at the RPC server caused a division by zero.
1770	A floating-point underflow occurred at the RPC server.
1771	A floating-point overflow occurred at the RPC server.
1772	The list of RPC servers available for the binding of auto handles has been exhausted.
1773	Unable to open the character translation table file.
1774	The file containing the character translation table has fewer than 512 bytes.
1775	A null context handle was passed from the client to the host during a remote procedure call.
1777	The context handle changed during a remote procedure call.
1778	The binding handles passed to a remote procedure call do not match.
1779	The stub is unable to get the remote procedure call handle.
1780	A null reference pointer was passed to the stub.
1781	The enumeration value is out of range.
1782	The byte count is too small.
1783	The stub received bad data.
1784	The supplied user buffer is not valid for the requested operation.
1785	The disk media is not recognized. It may not be formatted.
1786	The workstation does not have a trust secret.
1787	The security database on the server does not have a computer account for this workstation trust relationship.
1788	The trust relationship between the primary domain and the trusted domain failed.
1789	The trust relationship between this workstation and the primary domain failed.
1790	The network logon failed.
1791	A remote procedure call is already in progress for this thread.
1792	An attempt was made to logon, but the network logon service was not started.
1793	The user's account has expired.
1794	The redirector is in use and cannot be unloaded.
1795	The specified printer driver is already installed.
1796	The specified port is unknown.
1797	The printer driver is unknown.
1798	The print processor is unknown.
1799	The specified separator file is invalid.
1800	The specified priority is invalid.
1801	The printer name is invalid.
1802	The printer already exists.
1803	The printer command is invalid.
1804	The specified datatype is invalid.
1805	The environment specified is invalid.
1806	There are no more bindings.
1807	The account used is an interdomain trust account. Use your global user account or local user account to access this server.
1808	The account used is a computer account. Use your global user account or local user account to access this server.
1809	The account used is a server trust account. Use your global user account or local user account to access this server.
1810	The name or security ID (SID) of the domain specified is inconsistent with the trust information for that domain.
1811	The server is in use and cannot be unloaded.
1812	The specified image file did not contain a resource section.
1813	The specified resource type cannot be found in the image file.
1814	The specified resource name cannot be found in the image file.
1815	The specified resource language ID cannot be found in the image file.
1816	Not enough quota is available to process this command.
1817	No interfaces have been registered.
1818	The remote procedure call was cancelled.
1819	The binding handle does not contain all required information.
1820	A communications failure occurred during a remote procedure call.
1821	The requested authentication level is not supported.
1822	No principal name registered.
1823	The error specified is not a valid Windows RPC error code.
1824	A UUID that is valid only on this computer has been allocated.
1825	A security package specific error occurred.
1826	Thread is not canceled.
1827	Invalid operation on the encoding/decoding handle.
1828	Incompatible version of the serializing package.
1829	Incompatible version of the RPC stub.
1830	The RPC pipe object is invalid or corrupted.
1831	An invalid operation was attempted on an RPC pipe object.
1832	Unsupported RPC pipe version.
1898	The group member was not found.
1899	The endpoint mapper database entry could not be created.
1900	The object universal unique identifier (UUID) is the nil UUID.
1901	The specified time is invalid.
1902	The specified form name is invalid.
1903	The specified form size is invalid.
1904	The specified printer handle is already being waited on
1905	The specified printer has been deleted.
1906	The state of the printer is invalid.
1907	The user's password must be changed before logging on the first time.
1908	Could not find the domain controller for this domain.
1909	The referenced account is currently locked out and may not be logged on to.
1910	The object exporter specified was not found.
1911	The object specified was not found.
1912	The object resolver set specified was not found.
1913	Some data remains to be sent in the request buffer.
1914	Invalid asynchronous remote procedure call handle.
1915	Invalid asynchronous RPC call handle for this operation.
1916	The RPC pipe object has already been closed.
1917	The RPC call completed before all pipes were processed.
1918	No more data is available from the RPC pipe.
1919	No site name is available for this machine.
1920	The file can not be accessed by the system.
1921	The name of the file cannot be resolved by the system.
1922	The entry is not of the expected type.
1923	Not all object UUIDs could be exported to the specified entry.
1924	Interface could not be exported to the specified entry.
1925	The specified profile entry could not be added.
1926	The specified profile element could not be added.
1927	The specified profile element could not be removed.
1928	The group element could not be added.
1929	The group element could not be removed.
1930	The printer driver is not compatible with a policy enabled on your computer that blocks NT 4.0 drivers.
1931	The context has expired and can no longer be used.
2000	The pixel format is invalid.
2001	The specified driver is invalid.
2002	The window style or class attribute is invalid for this operation.
2003	The requested metafile operation is not supported.
2004	The requested transformation operation is not supported.
2005	The requested clipping operation is not supported.
2010	The specified color management module is invalid.
2011	The specified color profile is invalid.
2012	The specified tag was not found.
2013	A required tag is not present.
2014	The specified tag is already present.
2015	The specified color profile is not associated with any device.
2016	The specified color profile was not found.
2017	The specified color space is invalid.
2018	Image Color Management is not enabled.
2019	There was an error while deleting the color transform.
2020	The specified color transform is invalid.
2021	The specified transform does not match the bitmap's color space.
2022	The specified named color index is not present in the profile.
2102	The workstation driver is not installed.
2103	The server could not be located.
2104	An internal error occurred. The network cannot access a shared memory segment.
2105	A network resource shortage occurred .
2106	This operation is not supported on workstations.
2107	The device is not connected.
2108	The network connection was made successfully, but the user had to be prompted for a password other than the one originally specified.
2109	The network connection was made successfully using default credentials.
2114	The Server service is not started.
2115	The queue is empty.
2116	The device or directory does not exist.
2117	The operation is invalid on a redirected resource.
2118	The name has already been shared.
2119	The server is currently out of the requested resource.
2121	Requested addition of items exceeds the maximum allowed.
2122	The Peer service supports only two simultaneous users.
2123	The API return buffer is too small.
2127	A remote API error occurred.
2131	An error occurred when opening or reading the configuration file.
2136	A general network error occurred.
2137	The Workstation service is in an inconsistent state. Restart the computer before restarting the Workstation service.
2138	The Workstation service has not been started.
2139	The requested information is not available.
2140	An internal Windows 2000 error occurred.
2141	The server is not configured for transactions.
2142	The requested API is not supported on the remote server.
2143	The event name is invalid.
2144	The computer name already exists on the network. Change it and restart the computer.
2146	The specified component could not be found in the configuration information.
2147	The specified parameter could not be found in the configuration information.
2149	A line in the configuration file is too long.
2150	The printer does not exist.
2151	The print job does not exist.
2152	The printer destination cannot be found.
2153	The printer destination already exists.
2154	The printer queue already exists.
2155	No more printers can be added.
2156	No more print jobs can be added.
2157	No more printer destinations can be added.
2158	This printer destination is idle and cannot accept control operations.
2159	This printer destination request contains an invalid control function.
2160	The print processor is not responding.
2161	The spooler is not running.
2162	This operation cannot be performed on the print destination in its current state.
2163	This operation cannot be performed on the printer queue in its current state.
2164	This operation cannot be performed on the print job in its current state.
2165	A spooler memory allocation failure occurred.
2166	The device driver does not exist.
2167	The data type is not supported by the print processor.
2168	The print processor is not installed.
2180	The service database is locked.
2181	The service table is full.
2182	The requested service has already been started.
2183	The service does not respond to control actions.
2184	The service has not been started.
2185	The service name is invalid.
2186	The service is not responding to the control function.
2187	The service control is busy.
2188	The configuration file contains an invalid service program name.
2189	The service could not be controlled in its present state.
2190	The service ended abnormally.
2191	The requested pause or stop is not valid for this service.
2192	The service control dispatcher could not find the service name in the dispatch table.
2193	The service control dispatcher pipe read failed.
2194	A thread for the new service could not be created.
2200	This workstation is already logged on to the local-area network.
2201	The workstation is not logged on to the local-area network.
2202	The specified username is invalid.
2203	The password parameter is invalid.
2204	The logon processor did not add the message alias.
2205	The logon processor did not add the message alias.
2206	The logoff processor did not delete the message alias.
2207	The logoff processor did not delete the message alias.
2209	Network logons are paused.
2210	A centralized logon-server conflict occurred.
2211	The server is configured without a valid user path.
2212	An error occurred while loading or running the logon script.
2214	The logon server was not specified. Your computer will be logged on as STANDALONE.
2215	The logon server could not be found.
2216	There is already a logon domain for this computer.
2217	The logon server could not validate the logon.
2219	The security database could not be found.
2220	The group name could not be found.
2221	The user name could not be found.
2222	The resource name could not be found.
2223	The group already exists.
2224	The account already exists.
2225	The resource permission list already exists.
2226	This operation is only allowed on the primary domain controller of the domain.
2227	The security database has not been started.
2228	There are too many names in the user accounts database.
2229	A disk I/O failure occurred.
2230	The limit of 64 entries per resource was exceeded.
2231	Deleting a user with a session is not allowed.
2232	The parent directory could not be located.
2233	Unable to add to the security database session cache segment.
2234	This operation is not allowed on this special group.
2235	This user is not cached in user accounts database session cache.
2236	The user already belongs to this group.
2237	The user does not belong to this group.
2238	This user account is undefined.
2239	This user account has expired.
2240	The user is not allowed to log on from this workstation.
2241	The user is not allowed to log on at this time.
2242	The password of this user has expired.
2243	The password of this user cannot change.
2244	This password cannot be used now.
2245	The password does not meet the password policy requirements. Check the minimum password length, password complexity and password history requirements.
2246	The password of this user is too recent to change.
2247	The security database is corrupted.
2248	No updates are necessary to this replicant network/local security database.
2249	This replicant database is outdated; synchronization is required.
2250	This network connection does not exist.
2251	This asg_type is invalid.
2252	This device is currently being shared.
2270	The computer name could not be added as a message alias. The name may already exist on the network.
2271	The Messenger service is already started.
2272	The Messenger service failed to start.
2273	The message alias could not be found on the network.
2274	This message alias has already been forwarded.
2275	This message alias has been added but is still forwarded.
2276	This message alias already exists locally.
2277	The maximum number of added message aliases has been exceeded.
2278	The computer name could not be deleted.
2279	Messages cannot be forwarded back to the same workstation.
2280	An error occurred in the domain message processor.
2281	The message was sent, but the recipient has paused the Messenger service.
2282	The message was sent but not received.
2283	The message alias is currently in use. Try again later.
2284	The Messenger service has not been started.
2285	The name is not on the local computer.
2286	The forwarded message alias could not be found on the network.
2287	The message alias table on the remote station is full.
2288	Messages for this alias are not currently being forwarded.
2289	The broadcast message was truncated.
2294	This is an invalid device name.
2295	A write fault occurred.
2297	A duplicate message alias exists on the network.
2298	This message alias will be deleted later.
2299	The message alias was not successfully deleted from all networks.
2300	This operation is not supported on computers with multiple networks.
2310	This shared resource does not exist.
2311	This device is not shared.
2312	A session does not exist with that computer name.
2314	There is not an open file with that identification number.
2315	A failure occurred when executing a remote administration command.
2316	A failure occurred when opening a remote temporary file.
2317	The data returned from a remote administration command has been truncated to 64K.
2318	This device cannot be shared as both a spooled and a non-spooled resource.
2319	The information in the list of servers may be incorrect.
2320	The computer is not active in this domain.
2321	The share must be removed from the Distributed File System before it can be deleted.
2331	The operation is invalid for this device.
2332	This device cannot be shared.
2333	This device was not open.
2334	This device name list is invalid.
2335	The queue priority is invalid.
2337	There are no shared communication devices.
2338	The queue you specified does not exist.
2340	This list of devices is invalid.
2341	The requested device is invalid.
2342	This device is already in use by the spooler.
2343	This device is already in use as a communication device.
2351	This computer name is invalid.
2354	The string and prefix specified are too long.
2356	This path component is invalid.
2357	Could not determine the type of input.
2362	The buffer for types is not big enough.
2370	Profile files cannot exceed 64K.
2371	The start offset is out of range.
2372	The system cannot delete current connections to network resources.
2373	The system was unable to parse the command line in this file.
2374	An error occurred while loading the profile file.
2375	Errors occurred while saving the profile file. The profile was partially saved.
2378	This log file has changed between reads.
2380	The source path cannot be a directory.
2381	The source path is illegal.
2382	The destination path is illegal.
2383	The source and destination paths are on different servers.
2385	The Run server you requested is paused.
2389	An error occurred when communicating with a Run server.
2391	An error occurred when starting a background process.
2392	The shared resource you are connected to could not be found.
2400	The LAN adapter number is invalid.
2401	This network connection has files open or requests pending.
2402	Active connections still exist.
2403	This share name or password is invalid.
2404	The device is in use by an active process and cannot be disconnected.
2405	The drive letter is in use locally.
2430	The specified client is already registered for the specified event.
2431	The alert table is full.
2432	An invalid or nonexistent alert name was raised.
2433	The alert recipient is invalid.
2434	A user's session with this server has been deleted because the user's logon hours are no longer valid.
2440	The log file does not contain the requested record number.
2450	The user accounts database is not configured correctly.
2451	This operation is not permitted when the Netlogon service is running.
2452	This operation is not allowed on the last administrative account.
2453	Could not find domain controller for this domain.
2454	Could not set logon information for this user.
2455	The Netlogon service has not been started.
2456	Unable to add to the user accounts database.
2457	This server's clock is not synchronized with the primary domain controller's clock.
2458	A password mismatch has been detected.
2460	The server identification does not specify a valid server.
2461	The session identification does not specify a valid session.
2462	The connection identification does not specify a valid connection.
2463	There is no space for another entry in the table of available servers.
2464	The server has reached the maximum number of sessions it supports.
2465	The server has reached the maximum number of connections it supports.
2466	The server cannot open more files because it has reached its maximum number.
2467	There are no alternate servers registered on this server.
2470	Try down-level (remote admin protocol) version of API instead.
2480	The UPS driver could not be accessed by the UPS service.
2481	The UPS service is not configured correctly.
2482	The UPS service could not access the specified Comm Port.
2483	The UPS indicated a line fail or low battery situation. Service not started.
2484	The UPS service failed to perform a system shut down.
2500	The program below returned an MS-DOS error code:
2501	The program below needs more memory:
2502	The program below called an unsupported MS-DOS function:
2503	The workstation failed to boot.
2504	The file below is corrupt.
2505	No loader is specified in the boot-block definition file.
2506	NetBIOS returned an error: The NCB and SMB are dumped above.
2507	A disk I/O error occurred.
2508	Image parameter substitution failed.
2509	Too many image parameters cross disk sector boundaries.
2510	The image was not generated from an MS-DOS diskette formatted with /S.
2511	Remote boot will be restarted later.
2512	The call to the Remoteboot server failed.
2513	Cannot connect to the Remoteboot server.
2514	Cannot open image file on the Remoteboot server.
2515	Connecting to the Remoteboot server...
2516	Connecting to the Remoteboot server...
2517	Remote boot service was stopped; check the error log for the cause of the problem.
2518	Remote boot startup failed; check the error log for the cause of the problem.
2519	A second connection to a Remoteboot resource is not allowed.
2550	The browser service was configured with MaintainServerList=No.
2610	Service failed to start since none of the network adapters started with this service.
2611	Service failed to start due to bad startup information in the registry.
2612	Service failed to start because its database is absent or corrupt.
2613	Service failed to start because RPLFILES share is absent.
2614	Service failed to start because RPLUSER group is absent.
2615	Cannot enumerate service records.
2616	Workstation record information has been corrupted.
2617	Workstation record was not found.
2618	Workstation name is in use by some other workstation.
2619	Profile record information has been corrupted.
2620	Profile record was not found.
2621	Profile name is in use by some other profile.
2622	There are workstations using this profile.
2623	Configuration record information has been corrupted.
2624	Configuration record was not found.
2625	Adapter id record information has been corrupted.
2626	An internal service error has occurred.
2627	Vendor id record information has been corrupted.
2628	Boot block record information has been corrupted.
2629	The user account for this workstation record is missing.
2630	The RPLUSER local group could not be found.
2631	Boot block record was not found.
2632	Chosen profile is incompatible with this workstation.
2633	Chosen network adapter id is in use by some other workstation.
2634	There are profiles using this configuration.
2635	There are workstations, profiles or configurations using this boot block.
2636	Service failed to backup Remoteboot database.
2637	Adapter record was not found.
2638	Vendor record was not found.
2639	Vendor name is in use by some other vendor record.
2640	(boot name, vendor id) is in use by some other boot block record.
2641	Configuration name is in use by some other configuration.
2660	The internal database maintained by the DFS service is corrupt
2661	One of the records in the internal DFS database is corrupt
2662	There is no DFS name whose entry path matches the input Entry Path
2663	A root or link with the given name already exists
2664	The server share specified is already shared in the DFS
2665	The indicated server share does not support the indicated DFS namespace
2666	The operation is not valid on this portion of the namespace
2667	The operation is not valid on this portion of the namespace
2668	The operation is ambiguous because the link has multiple servers
2669	Unable to create a link
2670	The server is not DFS Aware
2671	The specified rename target path is invalid
2672	The specified DFS link is offline
2673	The specified server is not a server for this link
2674	A cycle in the DFS name was detected
2675	The operation is not supported on a server-based DFS
2676	This link is already supported by the specified server-share
2677	Can't remove the last server-share supporting this root or link
2678	The operation is not supported for an Inter-DFS link
2679	The internal state of the DFS Service has become inconsistent
2680	The DFS Service has been installed on the specified server
2681	The DFS data being reconciled is identical
2682	The DFS root cannot be deleted - Uninstall DFS if required
2683	A child or parent directory of the share is already in a DFS
2690	DFS internal error
2691	This machine is already joined to a domain.
2692	This machine is not currently joined to a domain.
2693	This machine is a domain controller and cannot be unjoined from a domain.
2694	The destination domain controller does not support creating machine accounts in OUs.
2695	The specified workgroup name is invalid.
2696	The specified computer name is incompatible with the default language used on the domain controller.
2697	The specified computer account could not be found.
2698	This version of Windows cannot be joined to a domain.
2999	This is the last error in NERR range.
3000	The specified print monitor is unknown.
3001	The specified printer driver is currently in use.
3002	The spool file was not found.
3003	A StartDocPrinter call was not issued.
3004	An AddJob call was not issued.
3005	The specified print processor has already been installed.
3006	The specified print monitor has already been installed.
3007	The specified print monitor does not have the required functions.
3008	The specified print monitor is currently in use.
3009	The requested operation is not allowed when there are jobs queued to the printer.
3010	The requested operation is successful. Changes will not be effective until the system is rebooted.
3011	The requested operation is successful. Changes will not be effective until the service is restarted.
3012	No printers were found.
3013	The printer driver is known to be unreliable.
3014	The printer driver is known to harm the system.
3023	There is a problem with a configuration of user specified shut down command file. The UPS service started anyway.
3029	Local security could not be started because the user accounts database (NET.ACC) was missing or corrupted, and no usable backup database was present. THE SYSTEM IS NOT SECURE.
3037	@I *LOGON HOURS
3039	Replicator limit for files in a directory has been exceeded.
3040	Replicator limit for tree depth has been exceeded.
3046	Cannot log on. User is currently logged on and argument TRYUSER is set to NO.
3052	The required parameter was not provided on the command line or in the configuration file.
3054	A request for resource could not be satisfied.
3055	A problem exists with the system configuration.
3056	A system error has occurred.
3057	An internal consistency error has occurred.
3058	The configuration file or the command line has an ambiguous option.
3059	The configuration file or the command line has a duplicate parameter.
3060	The service did not respond to control and was stopped with the DosKillProc function.
3061	An error occurred when attempting to run the service program.
3062	The sub-service failed to start.
3064	There is a problem with the file.
3070	memory
3071	disk space
3072	thread
3073	process
3074	Security Failure.
3075	Bad or missing LAN Manager root directory.
3076	The network software is not installed.
3077	The server is not started.
3078	The server cannot access the user accounts database (NET.ACC).
3079	Incompatible files are installed in the LANMAN tree.
3080	The LANMANLOGS directory is invalid.
3081	The domain specified could not be used.
3082	The computer name is being used as a message alias on another computer.
3083	The announcement of the server name failed.
3084	The user accounts database is not configured correctly.
3085	The server is not running with user-level security.
3087	The workstation is not configured properly.
3088	View your error log for details.
3089	Unable to write to this file.
3090	ADDPAK file is corrupted. Delete LANMANNETPROGADDPAK.SER and reapply all ADDPAKs.
3091	The LM386 server cannot be started because CACHE.EXE is not running.
3092	There is no account for this computer in the security database.
3093	This computer is not a member of the group SERVERS.
3094	The group SERVERS is not present in the local security database.
3095	This computer is configured as a member of a workgroup, not as a member of a domain. The Netlogon service does not need to run in this configuration.
3096	The primary Domain Controller for this domain could not be located.
3098	The service failed to authenticate with the primary domain controller.
3099	There is a problem with the security database creation date or serial number.
3100	The operation failed because a network software error occurred.
3102	The service failed to obtain a long-term lock on the segment for network control blocks (NCBs). The error code is the data.
3103	The service failed to release the long-term lock on the segment for network control blocks (NCBs). The error code is the data.
3106	An unexpected network control block (NCB) was received. The NCB is the data.
3107	The network is not started.
3108	A DosDevIoctl or DosFsCtl to NETWKSTA.SYS failed. The data shown is in this format: DWORD approx CS:IP of call to ioctl or fsctl WORD error code WORD ioctl or fsctl number
3111	An unexpected NetBIOS error occurred. The error code is the data.
3112	An illegal server message block (SMB) was received. The SMB is the data.
3114	Some entries in the error log were lost because of a buffer overflow.
3120	Initialization parameters controlling resource usage other than net buffers are sized so that too much memory is needed.
3121	The server cannot increase the size of a memory segment.
3124	The server failed to start. Either all three chdev parameters must be zero or all three must be nonzero.
3129	The server cannot update the AT schedule file. The file is corrupted.
3130	The server encountered an error when calling NetIMakeLMFileName. The error code is the data.
3132	Longterm lock of the server buffers failed. Check swap disk's free space and restart the system to start the server.
3140	The service has stopped due to repeated consecutive occurrences of a network control block (NCB) error. The last bad NCB follows in raw data.
3141	The Message server has stopped due to a lock on the Message server shared data segment.
3151	Unable to display message POPUP due to system VIO call error. The error code is the data.
3152	An illegal server message block (SMB) was received. The SMB is the data.
3160	The workstation information segment is bigger than 64K. The size follows, in DWORD format:
3161	The workstation was unable to get the name-number of the computer.
3162	The workstation could not initialize the Async NetBIOS Thread. The error code is the data.
3163	The workstation could not open the initial shared segment. The error code is the data.
3164	The workstation host table is full.
3165	A bad mailslot server message block (SMB) was received. The SMB is the data.
3166	The workstation encountered an error while trying to start the user accounts database. The error code is the data.
3167	The workstation encountered an error while responding to an SSI revalidation request. The function code and the error codes are the data.
3174	The server could not read the AT schedule file.
3175	The server found an invalid AT schedule record.
3176	The server could not find an AT schedule file so it created one.
3185	Local security could not be started because the user accounts database (NET.ACC) was missing or corrupted, and no usable backup database was present. THE SYSTEM IS NOT SECURE.
3204	The server could not create a thread. The THREADS parameter in the CONFIG.SYS file should be increased.
3213	Replicator limit for files in a directory has been exceeded.
3214	Replicator limit for tree depth has been exceeded.
3215	Unrecognized message received in mailslot.
3217	Cannot log on. User is currently logged on and argument TRYUSER is set to NO.
3230	A power failure was detected at the server.
3231	The UPS service performed server shut down.
3232	The UPS service did not complete execution of the user specified shut down command file.
3233	The UPS driver could not be opened. The error code is the data.
3234	Power has been restored.
3235	There is a problem with a configuration of user specified shut down command file.
3256	There was an unrecoverable error in the dynamic- link library of the service.
3257	The system returned an unexpected error code. The error code is the data.
3258	The fault-tolerance error log file, LANROOTLOGSFT.LOG, is more than 64K.
3259	The fault-tolerance error-log file, LANROOTLOGSFT.LOG, had the update in progress bit set upon opening, which means that the system crashed while working on the error log.
3301	Remote IPC
3302	Remote Admin
3303	Logon server share
3304	A network error occurred.
3400	There is not enough memory to start the Workstation service.
3401	An error occurred when reading the NETWORKS entry in the LANMAN.INI file.
3404	There are too many NETWORKS entries in the LANMAN.INI file.
3408	The program cannot be used with this operating system.
3409	The redirector is already installed.
3411	There was an error installing NETWKSTA.SYS. Press ENTER to continue.
3412	Resolver linkage problem.
3419	You have open files or devices, and a forced disconnection may cause you to lose data.
3420	Default Share for Internal Use
3421	Messenger Service
3500	The command completed successfully.
3501	You used an invalid option.
3503	The command contains an invalid number of arguments.
3504	The command completed with one or more errors.
3505	You used an option with an invalid value.
3510	A command was used with conflicting switches.
3512	The software requires a newer version of the operating system.
3513	More data is available than can be returned by Windows.
3515	This command can be used only on a Windows Domain Controller.
3516	This command cannot be used on a Windows Domain Controller.
3520	These Windows services are started:
3525	Stopping the Workstation service also stops the Server service.
3526	The workstation has open files.
3533	The service is starting or stopping. Please try again later.
3534	The service did not report an error.
3535	An error occurred controlling the device.
3660	These workstations have sessions on this server:
3661	These workstations have sessions with open files on this server:
3666	The message alias is forwarded.
3670	You have these remote connections:
3671	Continuing will cancel the connections.
3676	New connections will be remembered.
3677	New connections will not be remembered.
3678	An error occurred while saving your profile. The state of your remembered connections has not changed.
3679	An error occurred while reading your profile.
3682	No network services are started.
3683	There are no entries in the list.
3689	The Workstation service is already running. Windows will ignore command options for the workstation.
3694	The shared queue cannot be deleted while a print job is being spooled to the queue.
3710	An error occurred while opening the Help file.
3711	The Help file is empty.
3712	The Help file is corrupted.
3714	This operation is privileged on systems with earlier versions of the software.
3716	The device type is unknown.
3717	The log file has been corrupted.
3718	Program filenames must end with .EXE.
3719	A matching share could not be found so nothing was deleted.
3720	A bad value is in the units-per-week field of the user record.
3725	An error occurred when the share was deleted.
3726	The user name is invalid.
3727	The password is invalid.
3728	The passwords do not match.
3729	Your persistent connections were not all restored.
3730	This is not a valid computer name or domain name.
3732	Default permissions cannot be set for that resource.
3734	A valid password was not entered.
3735	A valid name was not entered.
3736	The resource named cannot be shared.
3737	The permissions string contains invalid permissions.
3738	You can only perform this operation on printers and communication devices.
3743	The server is not configured for remote administration.
3752	No users have sessions with this server.
3756	This is an invalid response.
3757	No valid response was provided.
3758	The destination list provided does not match the destination list of the printer queue.
3761	The time range specified ends before it starts.
3764	Time supplied is not exactly on the hour.
3765	12 and 24 hour time formats may not be mixed.
3767	An illegal date format has been supplied.
3768	An illegal day range has been supplied.
3769	An illegal time range has been supplied.
3770	Arguments to NET USER are invalid. Check the minimum password length and/or arguments supplied.
3771	The value for ENABLESCRIPT must be YES.
3773	An illegal country code has been supplied.
3774	The user was successfully created but could not be added to the USERS local group.
3775	The user context supplied is invalid.
3777	Sending files is no longer supported.
3778	You may not specify paths for ADMIN$ and IPC$ shares.
3784	Only disk shares can be marked as cacheable
3802	This schedule date is invalid.
3803	The LANMAN root directory is unavailable.
3804	The SCHED.LOG file could not be opened.
3805	The Server service has not been started.
3806	The AT job ID does not exist.
3807	The AT schedule file is corrupted.
3808	The delete failed due to a problem with the AT schedule file.
3809	The command line cannot exceed 259 characters.
3810	The AT schedule file could not be updated because the disk is full.
3812	The AT schedule file is invalid. Please delete the file and create a new one.
3813	The AT schedule file was deleted.
3814	The syntax of this command is: AT [id] [/DELETE] AT time [/EVERY:date \| /NEXT:date] command The AT command schedules a program command to run at a later date and time on a server. It also displays the list of programs and commands scheduled to be run.
3815	The AT command has timed-out. Please try again later.
3816	The minimum password age for user accounts cannot be greater than the maximum password age.
3817	You have specified a value that is incompatible with servers with down-level software. Please specify a lower value.
3901	****
3902	** unexpected end of message **
3905	Press ESC to exit
3906	...
3912	Could not locate a time-server.
3915	The user's home directory could not be determined.
3916	The user's home directory has not been specified.
3920	There are no available drive letters left.
3936	This computer is not currently configured to use a specific SNTP server.
3953	The syntax is incorrect.
3960	You specified an invalid file number.
3961	You specified an invalid print job number.
3963	The user or group account specified cannot be found.
3965	The user was added but could not be enabled for File and Print Services for NetWare.
3966	File and Print Services for NetWare is not installed.
3967	Cannot set user properties for File and Print Services for NetWare.
3969	NetWare compatible logon
4000	WINS encountered an error while processing the command.
4001	The local WINS can not be deleted.
4002	The importation from the file failed.
4003	The backup failed. Was a full backup done before?
4004	The backup failed. Check the directory to which you are backing the database.
4005	The name does not exist in the WINS database.
4006	Replication with a nonconfigured partner is not allowed.
4100	The DHCP client has obtained an IP address that is already in use on the network. The local interface will be disabled until the DHCP client can obtain a new address.
4200	The GUID passed was not recognized as valid by a WMI data provider.
4201	The instance name passed was not recognized as valid by a WMI data provider.
4202	The data item ID passed was not recognized as valid by a WMI data provider.
4203	The WMI request could not be completed and should be retried.
4204	The WMI data provider could not be located.
4205	The WMI data provider references an instance set that has not been registered.
4206	The WMI data block or event notification has already been enabled.
4207	The WMI data block is no longer available.
4208	The WMI data service is not available.
4209	The WMI data provider failed to carry out the request.
4210	The WMI MOF information is not valid.
4211	The WMI registration information is not valid.
4212	The WMI data block or event notification has already been disabled.
4213	The WMI data item or data block is read only.
4214	The WMI data item or data block could not be changed.
4300	The media identifier does not represent a valid medium.
4301	The library identifier does not represent a valid library.
4302	The media pool identifier does not represent a valid media pool.
4303	The drive and medium are not compatible or exist in different libraries.
4304	The medium currently exists in an offline library and must be online to perform this operation.
4305	The operation cannot be performed on an offline library.
4306	The library, drive, or media pool is empty.
4307	The library, drive, or media pool must be empty to perform this operation.
4308	No media is currently available in this media pool or library.
4309	A resource required for this operation is disabled.
4310	The media identifier does not represent a valid cleaner.
4311	The drive cannot be cleaned or does not support cleaning.
4312	The object identifier does not represent a valid object.
4313	Unable to read from or write to the database.
4314	The database is full.
4315	The medium is not compatible with the device or media pool.
4316	The resource required for this operation does not exist.
4317	The operation identifier is not valid.
4318	The media is not mounted or ready for use.
4319	The device is not ready for use.
4320	The operator or administrator has refused the request.
4321	The drive identifier does not represent a valid drive.
4322	Library is full. No slot is available for use.
4323	The transport cannot access the medium.
4324	Unable to load the medium into the drive.
4325	Unable to retrieve the drive status.
4326	Unable to retrieve the slot status.
4327	Unable to retrieve status about the transport.
4328	Cannot use the transport because it is already in use.
4329	Unable to open or close the inject/eject port.
4330	Unable to eject the medium because it is in a drive.
4331	A cleaner slot is already reserved.
4332	A cleaner slot is not reserved.
4333	The cleaner cartridge has performed the maximum number of drive cleanings.
4334	Unexpected on-medium identifier.
4335	The last remaining item in this group or resource cannot be deleted.
4336	The message provided exceeds the maximum size allowed for this parameter.
4337	The volume contains system or paging files.
4338	The media type cannot be removed from this library since at least one drive in the library reports it can support this media type.
4339	This offline media cannot be mounted on this system since no enabled drives are present which can be used.
4340	A cleaner cartridge is present in the tape library.
4341	(Y/N) [N]
4342	Error
4343	OK
4344	Y
4345	N
4346	Any
4347	A
4348	P
4349	(not found)
4350	The remote storage service was not able to recall the file.
4351	The remote storage service is not operational at this time.
4352	The remote storage service encountered a media error.
4354	Please type the password:
4358	Type a password for the user:
4359	Type the password for the shared resource:
4360	Type your password:
4361	Retype the password to confirm:
4362	Type the user's old password:
4363	Type the user's new password:
4364	Type your new password:
4365	Type the Replicator service password:
4368	Type your user name:
4372	Print job detail
4378	The following running services can be controlled:
4379	Statistics are available for the following running services:
4381	The syntax of this command is:
4382	The options of this command are:
4383	Please enter the name of the Primary Domain Controller:
4385	Sunday
4386	Monday
4387	Tuesday
4388	Wednesday
4389	Thursday
4390	The file or directory is not a reparse point.
4391	The reparse point attribute cannot be set because it conflicts with an existing attribute.
4392	The data present in the reparse point buffer is invalid.
4393	The tag present in the reparse point buffer is invalid.
4394	There is a mismatch between the tag specified in the request and the tag present in the reparse point.
4395	W
4396	Th
4397	F
4398	S
4399	Sa
4401	Group name
4402	Comment
4403	Members
4406	Alias name
4407	Comment
4408	Members
4411	User name
4412	Full Name
4413	Comment
4414	User's comment
4415	Parameters
4416	Country code
4417	Privilege level
4418	Operator privileges
4419	Account active
4420	Account expires
4421	Password last set
4422	Password expires
4423	Password changeable
4424	Workstations allowed
4425	Maximum disk space
4426	Unlimited
4427	Local Group Memberships
4428	Domain controller
4429	Logon script
4430	Last logon
4431	Global Group memberships
4432	Logon hours allowed
4433	All
4434	None
4436	Home directory
4437	Password required
4438	User may change password
4439	User profile
4440	Locked
4450	Computer name
4451	User name
4452	Software version
4453	Workstation active on
4454	Windows NT root directory
4455	Workstation domain
4456	Logon domain
4457	Other domain(s)
4458	COM Open Timeout (sec)
4459	COM Send Count (byte)
4460	COM Send Timeout (msec)
4461	DOS session print time-out (sec)
4462	Maximum error log size (K)
4463	Maximum cache memory (K)
4464	Number of network buffers
4465	Number of character buffers
4466	Size of network buffers
4467	Size of character buffers
4468	Full Computer name
4469	Workstation Domain DNS Name
4470	Windows 2002
4481	Server Name
4482	Server Comment
4483	Send administrative alerts to
4484	Software version
4485	Peer Server
4486	Windows NT
4487	Server Level
4488	Windows NT Server
4489	Server is active on
4492	Server hidden
4500	Single Instance Storage is not available on this volume.
4506	Maximum Logged On Users
4507	Maximum concurrent administrators
4508	Maximum resources shared
4509	Maximum connections to resources
4510	Maximum open files on server
4511	Maximum open files per session
4512	Maximum file locks
4520	Idle session time (min)
4526	Share-level
4527	User-level
4530	Unlimited Server
4570	Force user logoff how long after time expires?:
4571	Lock out account after how many bad passwords?:
4572	Minimum password age (days):
4573	Maximum password age (days):
4574	Minimum password length:
4575	Length of password history maintained:
4576	Computer role:
4577	Primary Domain controller for workstation domain:
4578	Lockout threshold:
4579	Lockout duration (minutes):
4580	Lockout observation window (minutes):
4600	Statistics since
4601	Sessions accepted
4602	Sessions timed-out
4603	Sessions errored-out
4604	Kilobytes sent
4605	Kilobytes received
4606	Mean response time (msec)
4607	Network errors
4608	Files accessed
4609	Print jobs spooled
4610	System errors
4611	Password violations
4612	Permission violations
4613	Communication devices accessed
4614	Sessions started
4615	Sessions reconnected
4616	Sessions starts failed
4617	Sessions disconnected
4618	Network I/O's performed
4619	Files and pipes accessed
4620	Times buffers exhausted
4621	Big buffers
4622	Request buffers
4626	Connections made
4627	Connections failed
4630	Bytes received
4631	Server Message Blocks (SMBs) received
4632	Bytes transmitted
4633	Server Message Blocks (SMBs) transmitted
4634	Read operations
4635	Write operations
4636	Raw reads denied
4637	Raw writes denied
4638	Network errors
4639	Connections made
4640	Reconnections made
4641	Server disconnects
4642	Sessions started
4643	Hung sessions
4644	Failed sessions
4645	Failed operations
4646	Use count
4647	Failed use count
4655	The message name forwarding was successfully canceled.
4661	The password was changed successfully.
4664	The message was successfully sent to all users of the network.
4666	The message was successfully sent to all users of this server.
4696	Windows NT Server
4697	Windows NT Workstation
4698	MS-DOS Enhanced Workstation
4700	Server Name Remark
4702	(UNC)
4703	...
4704	Domain
4706	Invalid network provider. Available networks are:
4710	Disk
4711	Print
4712	Comm
4713	IPC
4714	Status Local Remote Network
4715	OK
4716	Dormant
4717	Paused
4718	Disconnected
4719	Error
4720	Connecting
4721	Reconnecting
4722	Status
4723	Local name
4724	Remote name
4725	Resource type
4726	# Opens
4727	# Connections
4728	Unavailable
4730	Share name Resource Remark
4731	Share name
4732	Resource
4733	Spooled
4734	Permission
4735	Maximum users
4736	No limit
4737	Users
4739	Caching
4740	ID Path User name # Locks
4741	File ID
4742	Locks
4743	Permissions
4744	Share name
4745	Type
4746	Used as
4747	Comment
4750	Computer User name Client Type Opens Idle time
4751	Computer
4752	Sess time
4753	Idle time
4754	Share name Type # Opens
4755	Client type
4756	Guest logon
4770	Manual caching of documents
4771	Automatic caching of documents
4772	Automatic caching of programs and documents
4773	Caching disabled
4774	Automatic
4775	Manual
4776	Documents
4777	Programs
4778	None
4800	Name
4801	Forwarded to
4802	Forwarded to you from
4803	Users of this server
4804	Net Send has been interrupted by a Ctrl+Break from the user.
4810	Name Job # Size Status
4811	jobs
4812	Print
4813	Name
4814	Job #
4815	Size
4816	Status
4817	Separator file
4818	Comment
4819	Priority
4820	Print after
4821	Print until
4822	Print processor
4823	Additional info
4824	Parameters
4825	Print Devices
4826	Printer Active
4827	Printer held
4828	Printer error
4829	Printer being deleted
4830	Printer status unknown
4841	Job #
4842	Submitting user
4843	Notify
4844	Job data type
4845	Job parameters
4846	Waiting
4847	Held in queue
4848	Spooling
4849	Paused
4850	Offline
4851	Error
4852	Out of paper
4853	Intervention required
4854	Printing
4855	on
4862	Driver
4930	User name Type Date
4931	Lockout
4932	Service
4933	Server
4934	Server started
4935	Server paused
4936	Server continued
4937	Server stopped
4938	Session
4939	Logon Guest
4940	Logon User
4941	Logon Administrator
4942	Logoff normal
4943	Logon
4944	Logoff error
4945	Logoff auto-disconnect
4946	Logoff administrator-disconnect
4947	Logoff forced by logon restrictions
4948	Service
4957	Account
4964	Account system settings were modified
4965	Logon restriction
4966	Limit exceeded: UNKNOWN
4967	Limit exceeded: Logon hours
4968	Limit exceeded: Account expired
4969	Limit exceeded: Workstation ID invalid
4970	Limit exceeded: Account disabled
4971	Limit exceeded: Account deleted
4972	Share
4978	Bad password
4979	Administrator privilege required
4980	Access
4984	Access denied
4985	Unknown
4986	Other
4987	Duration:
4988	Duration: Not available
4989	Duration: Less than one second
4990	(none)
4994	Access ended
4995	Log on to network
4996	Logon denied
4997	Program Message Time
4999	Account unlocked by administrator
5000	Log off network
5001	The cluster resource cannot be moved to another group because other resources are dependent on it.
5002	The cluster resource dependency cannot be found.
5003	The cluster resource cannot be made dependent on the specified resource because it is already dependent.
5004	The cluster resource is not online.
5005	A cluster node is not available for this operation.
5006	The cluster resource is not available.
5007	The cluster resource could not be found.
5008	The cluster is being shut down.
5009	A cluster node cannot be evicted from the cluster unless the node is down or it is the last node.
5010	The object already exists.
5011	The object is already in the list.
5012	The cluster group is not available for any new requests.
5013	The cluster group could not be found.
5014	The operation could not be completed because the cluster group is not online.
5015	The cluster node is not the owner of the resource.
5016	The cluster node is not the owner of the group.
5017	The cluster resource could not be created in the specified resource monitor.
5018	The cluster resource could not be brought online by the resource monitor.
5019	The operation could not be completed because the cluster resource is online.
5020	The cluster resource could not be deleted or brought offline because it is the quorum resource.
5021	The cluster could not make the specified resource a quorum resource because it is not capable of being a quorum resource.
5022	The cluster software is shutting down.
5023	The group or resource is not in the correct state to perform the requested operation.
5024	The properties were stored but not all changes will take effect until the next time the resource is brought online.
5025	The cluster could not make the specified resource a quorum resource because it does not belong to a shared storage class.
5026	The cluster resource could not be deleted since it is a core resource.
5027	The quorum resource failed to come online.
5028	The quorum log could not be created or mounted successfully.
5029	The cluster log is corrupt.
5030	The record could not be written to the cluster log since it exceeds the maximum size.
5031	The cluster log exceeds its maximum size.
5032	No checkpoint record was found in the cluster log.
5033	The minimum required disk space needed for logging is not available.
5034	The cluster node failed to take control of the quorum resource because the resource is owned by another active node.
5035	A cluster network is not available for this operation.
5036	A cluster node is not available for this operation.
5037	All cluster nodes must be running to perform this operation.
5038	A cluster resource failed.
5039	The cluster node is not valid.
5040	The cluster node already exists.
5041	A node is in the process of joining the cluster.
5042	The cluster node was not found.
5043	The cluster local node information was not found.
5044	The cluster network already exists.
5045	The cluster network was not found.
5046	The cluster network interface already exists.
5047	The cluster network interface was not found.
5048	The cluster request is not valid for this object.
5049	The cluster network provider is not valid.
5050	The cluster node is down.
5051	The cluster node is not reachable.
5052	The cluster node is not a member of the cluster.
5053	A cluster join operation is not in progress.
5054	The cluster network is not valid.
5055	Mar
5056	The cluster node is up.
5057	The cluster IP address is already in use.
5058	The cluster node is not paused.
5059	No cluster security context is available.
5060	The cluster network is not configured for internal cluster communication.
5061	The cluster node is already up.
5062	The cluster node is already down.
5063	The cluster network is already online.
5064	The cluster network is already offline.
5065	The cluster node is already a member of the cluster.
5066	The cluster network is the only one configured for internal cluster communication between two or more active cluster nodes. The internal communication capability cannot be removed from the network.
5067	One or more cluster resources depend on the network to provide service to clients. The client access capability cannot be removed from the network.
5068	This operation cannot be performed on the cluster resource as it the quorum resource. You may not bring the quorum resource offline or modify its possible owners list.
5069	The cluster quorum resource is not allowed to have any dependencies.
5070	The cluster node is paused.
5071	The cluster resource cannot be brought online. The owner node cannot run this resource.
5072	The cluster node is not ready to perform the requested operation.
5073	The cluster node is shutting down.
5074	The cluster join operation was aborted.
5075	The cluster join operation failed due to incompatible software versions between the joining node and its sponsor.
5076	This resource cannot be created because the cluster has reached the limit on the number of resources it can monitor.
5077	The system configuration changed during the cluster join or form operation. The join or form operation was aborted.
5078	The specified resource type was not found.
5079	The specified node does not support a resource of this type. This may be due to version inconsistencies or due to the absence of the resource DLL on this node.
5080	The specified resource name is not supported by this resource DLL. This may be due to a bad (or changed) name supplied to the resource DLL.
5081	No authentication package could be registered with the RPC server.
5082	You cannot bring the group online because the owner of the group is not in the preferred list for the group. To change the owner node for the group, move the group.
5083	The join operation failed because the cluster database sequence number has changed or is incompatible with the locker node. This may happen during a join operation if the cluster database was changing during the join.
5084	The resource monitor will not allow the fail operation to be performed while the resource is in its current state. This may happen if the resource is in a pending state.
5085	A non locker code got a request to reserve the lock for making global updates.
5086	The quorum disk could not be located by the cluster service.
5087	The backed up cluster database is possibly corrupt.
5088	A DFS root already exists in this cluster node.
5089	An attempt to modify a resource property failed because it conflicts with another existing property.
5090	Spain
5091	Denmark
5092	Sweden
5093	Norway
5094	Germany
5095	Australia
5096	Japan
5097	Korea
5098	China (PRC)
5099	Taiwan
5100	Asia
5101	Portugal
5102	Finland
5103	Arabic
5104	Hebrew
5153	The UPS service is about to perform final shut down.
5170	The Workstation must be started with the NET START command.
5175	Remote IPC
5176	Remote Admin
5177	Default share
5291	Never
5292	Never
5293	Never
5295	NET.HLP
5296	NET.HLP
5300	The network control block (NCB) request completed successfully. The NCB is the data.
5301	Illegal network control block (NCB) buffer length on SEND DATAGRAM, SEND BROADCAST, ADAPTER STATUS, or SESSION STATUS. The NCB is the data.
5302	The data descriptor array specified in the network control block (NCB) is invalid. The NCB is the data.
5303	The command specified in the network control block (NCB) is illegal. The NCB is the data.
5304	The message correlator specified in the network control block (NCB) is invalid. The NCB is the data.
5305	A network control block (NCB) command timed-out. The session may have terminated abnormally. The NCB is the data.
5306	An incomplete network control block (NCB) message was received. The NCB is the data.
5307	The buffer address specified in the network control block (NCB) is illegal. The NCB is the data.
5308	The session number specified in the network control block (NCB) is not active. The NCB is the data.
5309	No resource was available in the network adapter. The network control block (NCB) request was refused. The NCB is the data.
5310	The session specified in the network control block (NCB) was closed. The NCB is the data.
5311	The network control block (NCB) command was canceled. The NCB is the data.
5312	The message segment specified in the network control block (NCB) is illogical. The NCB is the data.
5313	The name already exists in the local adapter name table. The network control block (NCB) request was refused. The NCB is the data.
5314	The network adapter name table is full. The network control block (NCB) request was refused. The NCB is the data.
5315	The network name has active sessions and is now de-registered. The network control block (NCB) command completed. The NCB is the data.
5316	A previously issued Receive Lookahead command is active for this session. The network control block (NCB) command was rejected. The NCB is the data.
5317	The local session table is full. The network control block (NCB) request was refused. The NCB is the data.
5318	A network control block (NCB) session open was rejected. No LISTEN is outstanding on the remote computer. The NCB is the data.
5319	The name number specified in the network control block (NCB) is illegal. The NCB is the data.
5320	The call name specified in the network control block (NCB) cannot be found or did not answer. The NCB is the data.
5321	The name specified in the network control block (NCB) was not found. Cannot put '*' or 00h in the NCB name. The NCB is the data.
5322	The name specified in the network control block (NCB) is in use on a remote adapter. The NCB is the data.
5323	The name specified in the network control block (NCB) has been deleted. The NCB is the data.
5324	The session specified in the network control block (NCB) ended abnormally. The NCB is the data.
5325	The network protocol has detected two or more identical names on the network. The network control block (NCB) is the data.
5326	An unexpected protocol packet was received. There may be an incompatible remote device. The network control block (NCB) is the data.
5333	The NetBIOS interface is busy. The network control block (NCB) request was refused. The NCB is the data.
5334	There are too many network control block (NCB) commands outstanding. The NCB request was refused. The NCB is the data.
5335	The adapter number specified in the network control block (NCB) is illegal. The NCB is the data.
5336	The network control block (NCB) command completed while a cancel was occurring. The NCB is the data.
5337	The name specified in the network control block (NCB) is reserved. The NCB is the data.
5338	The network control block (NCB) command is not valid to cancel. The NCB is the data.
5351	There are multiple network control block (NCB) requests for the same session. The NCB request was refused. The NCB is the data.
5352	There has been a network adapter error. The only NetBIOS command that may be issued is an NCB RESET. The network control block (NCB) is the data.
5354	The maximum number of applications was exceeded. The network control block (NCB) request was refused. The NCB is the data.
5356	The requested resources are not available. The network control block (NCB) request was refused. The NCB is the data.
5364	A system error has occurred. The network control block (NCB) request was refused. The NCB is the data.
5365	A ROM checksum failure has occurred. The network control block (NCB) request was refused. The NCB is the data.
5366	A RAM test failure has occurred. The network control block (NCB) request was refused. The NCB is the data.
5367	A digital loopback failure has occurred. The network control block (NCB) request was refused. The NCB is the data.
5368	An analog loopback failure has occurred. The network control block (NCB) request was refused. The NCB is the data.
5369	An interface failure has occurred. The network control block (NCB) request was refused. The NCB is the data.
5370	An unrecognized network control block (NCB) return code was received. The NCB is the data.
5380	A network adapter malfunction has occurred. The network control block (NCB) request was refused. The NCB is the data.
5381	The network control block (NCB) command is still pending. The NCB is the data.
5509	Windows 2000 could not be started as configured. A previous working configuration was used instead.
5600	Could not share the User or Script path.
5601	The password for this computer is not found in the local security database.
5602	An internal error occurred while accessing the computer's local or network security database.
5705	The change log cache maintained by the Netlogon service for database changes is corrupted. The Netlogon service is resetting the change log.
5728	Could not load any transport.
5739	This domain has more global groups than can be replicated to a LanMan BDC. Either delete some of your global groups or remove the LanMan BDCs from the domain.
5742	Service failed to retrieve messages needed to boot remote boot clients.
5743	Service experienced a severe error and can no longer provide remote boot for 3Com 3Start remote boot clients.
5744	Service experienced a severe system error and will shut itself down.
5760	Service experienced error evaluating RPL configurations.
5761	Service experienced error creating RPL profiles for all configurations.
5762	Service experienced error accessing registry.
5763	Service experienced error replacing possibly outdated RPLDISK.SYS.
5764	Service experienced error adding security accounts or setting file permissions. These accounts are the RPLUSER local group and the user accounts for the individual RPL workstations.
5765	Service failed to back up its database.
5766	Service failed to initialize from its database. The database may be missing or corrupted. Service will attempt restoring the database from the backup.
5767	Service failed to restore its database from the backup. Service will not start.
5768	Service successfully restored its database from the backup.
5769	Service failed to initialize from its restored database. Service will not start.
5771	The Remoteboot database was in NT 3.5 / NT 3.51 format and NT is attempting to convert it to NT 4.0 format. The JETCONV converter will write to the Application event log when it is finished.
5781	Dynamic registration or deregistration of one or more DNS records failed because no DNS servers are available.
5890	An operation was attempted that is incompatible with the current membership state of the node.
5891	The quorum resource does not contain the quorum log.
5892	The membership engine requested shutdown of the cluster service on this node.
5893	The join operation failed because the cluster instance ID of the joining node does not match the cluster instance ID of the sponsor node.
5894	A matching network for the specified IP address could not be found. Please also specify a subnet mask and a cluster network.
5895	The actual data type of the property did not match the expected data type of the property.
5896	The cluster node was evicted from the cluster successfully, but the node was not cleaned up. Extended status information explaining why the node was not cleaned up is available.
5897	Two or more parameter values specified for a resource's properties are in conflict.
5898	This computer cannot be made a member of a cluster.
5899	This computer cannot be made a member of a cluster because it does not have the correct version of Windows installed.
5900	A cluster cannot be created with the specified cluster name because that cluster name is already in use. Specify a different name for the cluster.
6000	The specified file could not be encrypted.
6001	The specified file could not be decrypted.
6002	The specified file is encrypted and the user does not have the ability to decrypt it.
6003	There is no valid encryption recovery policy configured for this system.
6004	The required encryption driver is not loaded for this system.
6005	The file was encrypted with a different encryption driver than is currently loaded.
6006	There are no EFS keys defined for the user.
6007	The specified file is not encrypted.
6008	The specified file is not in the defined EFS export format.
6009	The specified file is read only.
6010	The directory has been disabled for encryption.
6011	The server is not trusted for remote encryption operation.
6012	Recovery policy configured for this system contains invalid recovery certificate.
6013	The encryption algorithm used on the source file needs a bigger key buffer than the one on the destination file.
6014	The disk partition does not support file encryption.
6015	This machine is disabled for file encryption.
6016	A newer system is required to decrypt this encrypted file.
6118	The list of servers for this workgroup is not currently available
6200	The Task Scheduler service must be configured to run in the System account to function properly. Individual tasks may be configured to run in other accounts.
7001	The specified session name is invalid.
7002	The specified protocol driver is invalid.
7003	The specified protocol driver was not found in the system path.
7004	The specified terminal connection driver was not found in the system path.
7005	A registry key for event logging could not be created for this session.
7006	A service with the same name already exists on the system.
7007	A close operation is pending on the session.
7008	There are no free output buffers available.
7009	The MODEM.INF file was not found.
7010	The modem name was not found in MODEM.INF.
7011	The modem did not accept the command sent to it. Verify that the configured modem name matches the attached modem.
7012	The modem did not respond to the command sent to it. Verify that the modem is properly cabled and powered on.
7013	Carrier detect has failed or carrier has been dropped due to disconnect.
7014	Dial tone not detected within the required time. Verify that the phone cable is properly attached and functional.
7015	Busy signal detected at remote site on callback.
7016	Voice detected at remote site on callback.
7017	Transport driver error
7022	The specified session cannot be found.
7023	The specified session name is already in use.
7024	The requested operation cannot be completed because the terminal connection is currently busy processing a connect, disconnect, reset, or delete operation.
7025	An attempt has been made to connect to a session whose video mode is not supported by the current client.
7035	The application attempted to enable DOS graphics mode. DOS graphics mode is not supported.
7037	Your interactive logon privilege has been disabled. Please contact your administrator.
7038	The requested operation can be performed only on the system console. This is most often the result of a driver or system DLL requiring direct console access.
7040	The client failed to respond to the server connect message.
7041	Disconnecting the console session is not supported.
7042	Reconnecting a disconnected session to the console is not supported.
7044	The request to control another session remotely was denied.
7045	The requested session access is denied.
7049	The specified terminal connection driver is invalid.
7050	The requested session cannot be controlled remotely. This may be because the session is disconnected or does not currently have a user logged on.
7051	The requested session is not configured to allow remote control.
7052	Your request to connect to this Terminal Server has been rejected. Your Terminal Server client license number is currently being used by another user. Please call your system administrator to obtain a unique license number.
7053	Your request to connect to this Terminal Server has been rejected. Your Terminal Server client license number has not been entered for this copy of the Terminal Server client. Please contact your system administrator.
7054	The system has reached its licensed logon limit. Please try again later.
7055	The client you are using is not licensed to use this system. Your logon request is denied.
7056	The system license has expired. Your logon request is denied.
7057	Remote control could not be terminated because the specified session is not currently being remotely controlled.
7058	The remote control of the console was terminated because the display mode was changed. Changing the display mode in a remote control session is not supported.
8001	The file replication service API was called incorrectly.
8002	The file replication service cannot be started.
8003	The file replication service cannot be stopped.
8004	The file replication service API terminated the request. The event log may have more information.
8005	The file replication service terminated the request. The event log may have more information.
8006	The file replication service cannot be contacted. The event log may have more information.
8007	The file replication service cannot satisfy the request because the user has insufficient privileges. The event log may have more information.
8008	The file replication service cannot satisfy the request because authenticated RPC is not available. The event log may have more information.
8009	The file replication service cannot satisfy the request because the user has insufficient privileges on the domain controller. The event log may have more information.
8010	The file replication service cannot satisfy the request because authenticated RPC is not available on the domain controller. The event log may have more information.
8011	The file replication service cannot communicate with the file replication service on the domain controller. The event log may have more information.
8012	The file replication service on the domain controller cannot communicate with the file replication service on this computer. The event log may have more information.
8013	The file replication service cannot populate the system volume because of an internal error. The event log may have more information.
8014	The file replication service cannot populate the system volume because of an internal timeout. The event log may have more information.
8015	The file replication service cannot process the request. The system volume is busy with a previous request.
8016	The file replication service cannot stop replicating the system volume because of an internal error. The event log may have more information.
8017	The file replication service detected an invalid parameter.
8200	An error occurred while installing the directory service. For more information, see the event log.
8201	The directory service evaluated group memberships locally.
8202	The specified directory service attribute or value does not exist.
8203	The attribute syntax specified to the directory service is invalid.
8204	The attribute type specified to the directory service is not defined.
8205	The specified directory service attribute or value already exists.
8206	The directory service is busy.
8207	The directory service is unavailable.
8208	The directory service was unable to allocate a relative identifier.
8209	The directory service has exhausted the pool of relative identifiers.
8210	The requested operation could not be performed because the directory service is not the master for that type of operation.
8211	The directory service was unable to initialize the subsystem that allocates relative identifiers.
8212	The requested operation did not satisfy one or more constraints associated with the class of the object.
8213	The directory service can perform the requested operation only on a leaf object.
8214	The directory service cannot perform the requested operation on the RDN attribute of an object.
8215	The directory service detected an attempt to modify the object class of an object.
8216	The requested cross-domain move operation could not be performed.
8217	Unable to contact the global catalog server.
8218	The policy object is shared and can only be modified at the root.
8219	The policy object does not exist.
8220	The requested policy information is only in the directory service.
8221	A domain controller promotion is currently active.
8222	A domain controller promotion is not currently active
8224	An operations error occurred.
8225	A protocol error occurred.
8226	The time limit for this request was exceeded.
8227	The size limit for this request was exceeded.
8228	The administrative limit for this request was exceeded.
8229	The compare response was false.
8230	The compare response was true.
8231	The requested authentication method is not supported by the server.
8232	A more secure authentication method is required for this server.
8233	Inappropriate authentication.
8234	The authentication mechanism is unknown.
8235	A referral was returned from the server.
8236	The server does not support the requested critical extension.
8237	This request requires a secure connection.
8238	Inappropriate matching.
8239	A constraint violation occurred.
8240	There is no such object on the server.
8241	There is an alias problem.
8242	An invalid dn syntax has been specified.
8243	The object is a leaf object.
8244	There is an alias dereferencing problem.
8245	The server is unwilling to process the request.
8246	A loop has been detected.
8247	There is a naming violation.
8248	The result set is too large.
8249	The operation affects multiple DSAs
8250	The server is not operational.
8251	A local error has occurred.
8252	An encoding error has occurred.
8253	A decoding error has occurred.
8254	The search filter cannot be recognized.
8255	One or more parameters are illegal.
8256	The specified method is not supported.
8257	No results were returned.
8258	The specified control is not supported by the server.
8259	A referral loop was detected by the client.
8260	The preset referral limit was exceeded.
8261	The search requires a SORT control.
8262	The search results exceed the offset range specified.
8301	The root object must be the head of a naming context. The root object cannot have an instantiated parent.
8302	The add replica operation cannot be performed. The naming context must be writable in order to create the replica.
8303	A reference to an attribute that is not defined in the schema occurred.
8304	The maximum size of an object has been exceeded.
8305	An attempt was made to add an object to the directory with a name that is already in use.
8306	An attempt was made to add an object of a class that does not have an RDN defined in the schema.
8307	An attempt was made to add an object using an RDN that is not the RDN defined in the schema.
8308	None of the requested attributes were found on the objects.
8309	The user buffer is too small.
8310	The attribute specified in the operation is not present on the object.
8311	Illegal modify operation. Some aspect of the modification is not permitted.
8312	The specified object is too large.
8313	The specified instance type is not valid.
8314	The operation must be performed at a master DSA.
8315	The object class attribute must be specified.
8316	A required attribute is missing.
8317	An attempt was made to modify an object to include an attribute that is not legal for its class.
8318	The specified attribute is already present on the object.
8320	The specified attribute is not present, or has no values.
8321	Mutliple values were specified for an attribute that can have only one value.
8322	A value for the attribute was not in the acceptable range of values.
8323	The specified value already exists.
8324	The attribute cannot be removed because it is not present on the object.
8325	The attribute value cannot be removed because it is not present on the object.
8326	The specified root object cannot be a subref.
8327	Chaining is not permitted.
8328	Chained evaluation is not permitted.
8329	The operation could not be performed because the object's parent is either uninstantiated or deleted.
8330	Having a parent that is an alias is not permitted. Aliases are leaf objects.
8331	The object and parent must be of the same type, either both masters or both replicas.
8332	The operation cannot be performed because child objects exist. This operation can only be performed on a leaf object.
8333	Directory object not found.
8334	The aliased object is missing.
8335	The object name has bad syntax.
8336	It is not permitted for an alias to refer to another alias.
8337	The alias cannot be dereferenced.
8338	The operation is out of scope.
8339	The operation cannot continue because the object is in the process of being removed.
8340	The DSA object cannot be deleted.
8341	A directory service error has occurred.
8342	The operation can only be performed on an internal master DSA object.
8343	The object must be of class DSA.
8344	Insufficient access rights to perform the operation.
8345	The object cannot be added because the parent is not on the list of possible superiors.
8346	Access to the attribute is not permitted because the attribute is owned by the Security Accounts Manager (SAM).
8347	The name has too many parts.
8348	The name is too long.
8349	The name value is too long.
8350	The directory service encountered an error parsing a name.
8351	The directory service cannot get the attribute type for a name.
8352	The name does not identify an object; the name identifies a phantom.
8353	The security descriptor is too short.
8354	The security descriptor is invalid.
8355	Failed to create name for deleted object.
8356	The parent of a new subref must exist.
8357	The object must be a naming context.
8358	It is not permitted to add an attribute which is owned by the system.
8359	The class of the object must be structural; you cannot instantiate an abstract class.
8360	The schema object could not be found.
8361	A local object with this GUID (dead or alive) already exists.
8362	The operation cannot be performed on a back link.
8363	The cross reference for the specified naming context could not be found.
8364	The operation could not be performed because the directory service is shutting down.
8365	The directory service request is invalid.
8366	The role owner attribute could not be read.
8367	The requested FSMO operation failed. The current FSMO holder could not be contacted.
8368	Modification of a DN across a naming context is not permitted.
8369	The attribute cannot be modified because it is owned by the system.
8370	Only the replicator can perform this function.
8371	The specified class is not defined.
8372	The specified class is not a subclass.
8373	The name reference is invalid.
8374	A cross reference already exists.
8375	It is not permitted to delete a master cross reference.
8376	Subtree notifications are only supported on NC heads.
8377	Notification filter is too complex.
8378	Schema update failed: duplicate RDN.
8379	Schema update failed: duplicate OID.
8380	Schema update failed: duplicate MAPI identifier.
8381	Schema update failed: duplicate schema-id GUID.
8382	Schema update failed: duplicate LDAP display name.
8383	Schema update failed: range-lower less than range upper.
8384	Schema update failed: syntax mismatch.
8385	Schema deletion failed: attribute is used in must-contain.
8386	Schema deletion failed: attribute is used in may-contain.
8387	Schema update failed: attribute in may-contain does not exist.
8388	Schema update failed: attribute in must-contain does not exist.
8389	Schema update failed: class in aux-class list does not exist or is not an auxiliary class.
8390	Schema update failed: class in poss-superiors does not exist.
8391	Schema update failed: class in subclassof list does not exist or does not satisfy hierarchy rules.
8392	Schema update failed: Rdn-Att-Id has wrong syntax.
8393	Schema deletion failed: class is used as auxiliary class.
8394	Schema deletion failed: class is used as sub class.
8395	Schema deletion failed: class is used as poss superior.
8396	Schema update failed in recalculating validation cache.
8397	The tree deletion is not finished. The request must be made again to continue deleting the tree.
8398	The requested delete operation could not be performed.
8399	Cannot read the governs class identifier for the schema record.
8400	The attribute schema has bad syntax.
8401	The attribute could not be cached.
8402	The class could not be cached.
8403	The attribute could not be removed from the cache.
8404	The class could not be removed from the cache.
8405	The distinguished name attribute could not be read.
8406	A required subref is missing.
8407	The instance type attribute could not be retrieved.
8408	An internal error has occurred.
8409	A database error has occurred.
8410	The attribute GOVERNSID is missing.
8411	An expected attribute is missing.
8412	The specified naming context is missing a cross reference.
8413	A security checking error has occurred.
8414	The schema is not loaded.
8415	Schema allocation failed. Please check if the machine is running low on memory.
8416	Failed to obtain the required syntax for the attribute schema.
8417	The global catalog verification failed. The global catalog is not available or does not support the operation. Some part of the directory is currently not available.
8418	The replication operation failed because of a schema mismatch between the servers involved.
8419	The DSA object could not be found.
8420	The naming context could not be found.
8421	The naming context could not be found in the cache.
8422	The child object could not be retrieved.
8423	The modification was not permitted for security reasons.
8424	The operation cannot replace the hidden record.
8425	The hierarchy file is invalid.
8426	The attempt to build the hierarchy table failed.
8427	The directory configuration parameter is missing from the registry.
8428	The attempt to count the address book indices failed.
8429	The allocation of the hierarchy table failed.
8430	The directory service encountered an internal failure.
8431	The directory service encountered an unknown failure.
8432	A root object requires a class of 'top'.
8433	This directory server is shutting down, and cannot take ownership of new floating single-master operation roles.
8434	The directory service is missing mandatory configuration information, and is unable to determine the ownership of floating single-master operation roles.
8435	The directory service was unable to transfer ownership of one or more floating single-master operation roles to other servers.
8436	The replication operation failed.
8437	An invalid parameter was specified for this replication operation.
8438	The directory service is too busy to complete the replication operation at this time.
8439	The distinguished name specified for this replication operation is invalid.
8440	The naming context specified for this replication operation is invalid.
8441	The distinguished name specified for this replication operation already exists.
8442	The replication system encountered an internal error.
8443	The replication operation encountered a database inconsistency.
8444	The server specified for this replication operation could not be contacted.
8445	The replication operation encountered an object with an invalid instance type.
8446	The replication operation failed to allocate memory.
8447	The replication operation encountered an error with the mail system.
8448	The replication reference information for the target server already exists.
8449	The replication reference information for the target server does not exist.
8450	The naming context cannot be removed because it is replicated to another server.
8451	The replication operation encountered a database error.
8452	The naming context is in the process of being removed or is not replicated from the specified server.
8453	Replication access was denied.
8454	The requested operation is not supported by this version of the directory service.
8455	The replication remote procedure call was cancelled.
8456	The source server is currently rejecting replication requests.
8457	The destination server is currently rejecting replication requests.
8458	The replication operation failed due to a collision of object names.
8459	The replication source has been reinstalled.
8460	The replication operation failed because a required parent object is missing.
8461	The replication operation was preempted.
8462	The replication synchronization attempt was abandoned because of a lack of updates.
8463	The replication operation was terminated because the system is shutting down.
8464	The replication synchronization attempt failed as the destination partial attribute set is not a subset of source partial attribute set.
8465	The replication synchronization attempt failed because a master replica attempted to sync from a partial replica.
8466	The server specified for this replication operation was contacted, but that server was unable to contact an additional server needed to complete the operation.
8467	The version of the Active Directory schema of the source forest is not compatible with the version of Active Directory on this computer. You must upgrade the operating system on a domain controller in the source forest before this computer can be added a
8468	Schema update failed: An attribute with the same link identifier already exists.
8469	Name translation: Generic processing error.
8470	Name translation: Could not find the name or insufficient right to see name.
8471	Name translation: Input name mapped to more than one output name.
8472	Name translation: Input name found, but not the associated output format.
8473	Name translation: Unable to resolve completely, only the domain was found.
8474	Name translation: Unable to perform purely syntactical mapping at the client without going out to the wire.
8475	Modification of a constructed att is not allowed.
8476	The OM-Object-Class specified is incorrect for an attribute with the specified syntax.
8477	The replication request has been posted; waiting for reply.
8478	The requested operation requires a directory service, and none was available.
8479	The LDAP display name of the class or attribute contains non-ASCII characters.
8480	The requested search operation is only supported for base searches.
8481	The search failed to retrieve attributes from the database.
8482	The schema update operation tried to add a backward link attribute that has no corresponding forward link.
8483	Source and destination of a cross-domain move do not agree on the object's epoch number. Either source or destination does not have the latest version of the object.
8484	Source and destination of a cross-domain move do not agree on the object's current name. Either source or destination does not have the latest version of the object.
8485	Source and destination for the cross-domain move operation are identical. Caller should use local move operation instead of cross-domain move operation.
8486	Source and destination for a cross-domain move are not in agreement on the naming contexts in the forest. Either source or destination does not have the latest version of the Partitions container.
8487	Destination of a cross-domain move is not authoritative for the destination naming context.
8488	Source and destination of a cross-domain move do not agree on the identity of the source object. Either source or destination does not have the latest version of the source object.
8489	Object being moved across-domains is already known to be deleted by the destination server. The source server does not have the latest version of the source object.
8490	Another operation which requires exclusive access to the PDC FSMO is already in progress.
8491	A cross-domain move operation failed such that two versions of the moved object exist - one each in the source and destination domains. The destination object needs to be removed to restore the system to a consistent state.
8492	This object may not be moved across domain boundaries either because cross-domain moves for this class are disallowed, or the object has some special characteristics, eg: trust account or restricted RID, which prevent its move.
8493	Can't move objects with memberships across domain boundaries as once moved, this would violate the membership conditions of the account group. Remove the object from any account group memberships and retry.
8494	A naming context head must be the immediate child of another naming context head, not of an interior node.
8495	The directory cannot validate the proposed naming context name because it does not hold a replica of the naming context above the proposed naming context. Please ensure that the domain naming master role is held by a server that is configured as a global
8496	Destination domain must be in native mode.
8497	The operation can not be performed because the server does not have an infrastructure container in the domain of interest.
8498	Cross-domain move of non-empty account groups is not allowed.
8499	Cross-domain move of non-empty resource groups is not allowed.
8500	The search flags for the attribute are invalid. The ANR bit is valid only on attributes of Unicode or Teletex strings.
8501	Tree deletions starting at an object which has an NC head as a descendant are not allowed.
8502	The directory service failed to lock a tree in preparation for a tree deletion because the tree was in use.
8503	The directory service failed to identify the list of objects to delete while attempting a tree deletion.
8505	Only an administrator can modify the membership list of an administrative group.
8506	Cannot change the primary group ID of a domain controller account.
8507	An attempt is made to modify the base schema.
8508	Adding a new mandatory attribute to an existing class, deleting a mandatory attribute from an existing class, or adding an optional attribute to the special class Top that is not a backlink attribute (directly or through inheritance, for example, by addin
8509	Schema update is not allowed on this DC because the DC is not the schema FSMO Role Owner.
8510	An object of this class cannot be created under the schema container. You can only create attribute-schema and class-schema objects under the schema container.
8511	The replica/child install failed to get the objectVersion attribute on the schema container on the source DC. Either the attribute is missing on the schema container or the credentials supplied do not have permission to read it.
8512	The replica/child install failed to read the objectVersion attribute in the SCHEMA section of the file schema.ini in the system32 directory.
8513	The specified group type is invalid.
8514	You cannot nest global groups in a mixed domain if the group is security-enabled.
8515	You cannot nest local groups in a mixed domain if the group is security-enabled.
8516	A global group cannot have a local group as a member.
8517	A global group cannot have a universal group as a member.
8518	A universal group cannot have a local group as a member.
8519	A global group cannot have a cross-domain member.
8520	A local group cannot have another cross domain local group as a member.
8521	A group with primary members cannot change to a security-disabled group.
8522	The schema cache load failed to convert the string default SD on a class-schema object.
8523	Only DSAs configured to be Global Catalog servers should be allowed to hold the Domain Naming Master FSMO role. (Applies only to Windows 2000 servers)
8524	The DSA operation is unable to proceed because of a DNS lookup failure.
8525	While processing a change to the DNS Host Name for an object, the Service Principal Name values could not be kept in sync.
8526	The Security Descriptor attribute could not be read.
8527	The object requested was not found, but an object with that key was found.
8528	The syntax of the linked attribute being added is incorrect. Forward links can only have syntax 2.5.5.1, 2.5.5.7, and 2.5.5.14, and backlinks can only have syntax 2.5.5.1
8529	Security Account Manager needs to get the boot password.
8530	Security Account Manager needs to get the boot key from floppy disk.
8531	Directory Service cannot start.
8532	Directory Services could not start.
8533	The connection between client and server requires packet privacy or better.
8534	The source domain may not be in the same forest as destination.
8535	The destination domain must be in the forest.
8536	The operation requires that destination domain auditing be enabled.
8537	The operation couldn't locate a DC for the source domain.
8538	The source object must be a group or user.
8539	The source object's SID already exists in destination forest.
8540	The source and destination object must be of the same type.
8542	Schema information could not be included in the replication request.
8543	The replication operation could not be completed due to a schema incompatibility.
8544	The replication operation could not be completed due to a previous schema incompatibility.
8545	The replication update could not be applied because either the source or the destination has not yet received information regarding a recent cross-domain move operation.
8546	The requested domain could not be deleted because there exist domain controllers that still host this domain.
8547	The requested operation can be performed only on a global catalog server.
8548	A local group can only be a member of other local groups in the same domain.
8549	Foreign security principals cannot be members of universal groups.
8550	The attribute is not allowed to be replicated to the GC because of security reasons.
8551	The checkpoint with the PDC could not be taken because there too many modifications being processed currently.
8552	The operation requires that source domain auditing be enabled.
8553	Security principal objects can only be created inside domain naming contexts.
8554	A Service Principal Name (SPN) could not be constructed because the provided hostname is not in the necessary format.
8555	A Filter was passed that uses constructed attributes.
8556	The unicodePwd attribute value must be enclosed in double quotes.
8557	Your computer could not be joined to the domain. You have exceeded the maximum number of computer accounts you are allowed to create in this domain. Contact your system administrator to have this limit reset or increased.
8558	For security reasons, the operation must be run on the destination DC.
8559	For security reasons, the source DC must be NT4SP4 or greater.
8560	Critical Directory Service System objects cannot be deleted during tree delete operations. The tree delete may have been partially performed.
8563	This version of Windows is too old to support the current directory forest behavior. You must upgrade the operating system on this server before it can become a domain controller in this forest.
8564	This version of Windows is too old to support the current domain behavior. You must upgrade the operating system on this server before it can become a domain controller in this domain.
8565	This version of Windows no longer supports the behavior version in use in this directory forest. You must advance the forest behavior version before this server can become a domain controller in the forest.
8566	This version of Windows no longer supports the behavior version in use in this domain. You must advance the domain behavior version before this server can become a domain controller in the domain.
8567	The version of Windows is incompatible with the behavior version of the domain or forest.
8568	The behavior version cannot be increased to the requested value because Domain Controllers still exist with versions lower than the requested value.
8569	The behavior version value cannot be increased while the domain is still in mixed domain mode. You must first change the domain to native mode before increasing the behavior version.
8570	The sort order requested is not supported.
8571	Found an object with a non unique name.
8572	The machine account was created pre-NT4. The account needs to be recreated.
8573	The database is out of version store.
8574	Unable to continue operation because multiple conflicting controls were used.
8575	Unable to find a valid security descriptor reference domain for this partition.
8576	Schema update failed: The link identifier is reserved.
8577	Schema update failed: There are no link identifiers available.
8578	A account group can not have a universal group as a member.
8579	Rename or move operations on naming context heads or read-only objects are not allowed.
8580	Move operations on objects in the schema naming context are not allowed.
8581	A system flag has been set on the object and does not allow the object to be moved or renamed.
8582	This object is not allowed to change its grandparent container. Moves are not forbidden on this object, but are restricted to sibling containers.
8583	Unable to resolve completely, a referral to another forest is generated.
8584	The requested action is not supported on standard server.
8585	Could not access a partition of the Active Directory located on a remote server. Make sure at least one server is running for the partition in question.
8586	The directory cannot validate the proposed naming context (or partition) name because it does not hold a replica nor can it contact a replica of the naming context above the proposed naming context. Please ensure that the parent naming context is properl
8587	The thread limit for this request was exceeded.
8588	The Global catalog server is not in the closest site.
8589	The DS cannot derive a service principal name (SPN) with which to mutually authenticate the target server because the corresponding server object in the local DS database has no serverReference attribute.
8590	The Directory Service failed to enter single user mode.
8591	The Directory Service cannot parse the script because of a syntax error.
8592	The Directory Service cannot process the script because of an error.
8593	The directory service cannot perform the requested operation because the servers involved are of different replication epochs (which is usually related to a domain rename that is in progress).
8594	The directory service binding must be renegotiated due to a change in the server extensions information.
8595	Operation not allowed on a disabled cross ref.
8596	Schema update failed: No values for msDS-IntId are available.
8597	Schema update failed: Duplicate msDS-INtId. Retry the operation.
8598	Schema deletion failed: attribute is used in rDNAttID.
8599	The directory service failed to authorize the request.
8600	The Directory Service cannot process the script because it is invalid.
8601	The remote create cross reference operation failed on the Domain Naming Master FSMO. The operation's error is in the extended data.
9001	DNS server unable to interpret format.
9002	DNS server failure.
9003	DNS name does not exist.
9004	DNS request not supported by name server.
9005	DNS operation refused.
9006	DNS name that ought not exist, does exist.
9007	DNS RR set that ought not exist, does exist.
9008	DNS RR set that ought to exist, does not exist.
9009	DNS server not authoritative for zone.
9010	DNS name in update or prereq is not in zone.
9016	DNS signature failed to verify.
9017	DNS bad key.
9018	DNS signature validity expired.
9501	No records found for given DNS query.
9502	Bad DNS packet.
9503	No DNS packet.
9504	DNS error, check rcode.
9505	Unsecured DNS packet.
9551	Invalid DNS type.
9552	Invalid IP address.
9553	Invalid property.
9554	Try DNS operation again later.
9555	Record for given name and type is not unique.
9556	DNS name does not comply with RFC specifications.
9557	DNS name is a fully-qualified DNS name.
9558	DNS name is dotted (multi-label).
9559	DNS name is a single-part name.
9560	DNS name contains an invalid character.
9561	DNS name is entirely numeric.
9562	The operation requested is not permitted on a DNS root server.
9601	DNS zone does not exist.
9602	DNS zone information not available.
9603	Invalid operation for DNS zone.
9604	Invalid DNS zone configuration.
9605	DNS zone has no start of authority (SOA) record.
9606	DNS zone has no Name Server (NS) record.
9607	DNS zone is locked.
9608	DNS zone creation failed.
9609	DNS zone already exists.
9610	DNS automatic zone already exists.
9611	Invalid DNS zone type.
9612	Secondary DNS zone requires master IP address.
9613	DNS zone not secondary.
9614	Need secondary IP address.
9615	WINS initialization failed.
9616	Need WINS servers.
9617	NBTSTAT initialization call failed.
9618	Invalid delete of start of authority (SOA)
9619	A conditional forwarding zone already exists for that name.
9620	This zone must be configured with one or more master DNS server IP addresses.
9621	The operation cannot be performed because this zone is shutdown.
9651	Primary DNS zone requires datafile.
9652	Invalid datafile name for DNS zone.
9653	Failed to open datafile for DNS zone.
9654	Failed to write datafile for DNS zone.
9655	Failure while reading datafile for DNS zone.
9701	DNS record does not exist.
9702	DNS record format error.
9703	Node creation failure in DNS.
9704	Unknown DNS record type.
9705	DNS record timed out.
9706	Name not in DNS zone.
9707	CNAME loop detected.
9708	Node is a CNAME DNS record.
9709	A CNAME record already exists for given name.
9710	Record only at DNS zone root.
9711	DNS record already exists.
9712	Secondary DNS zone data error.
9713	Could not create DNS cache data.
9714	DNS name does not exist.
9715	Could not create pointer (PTR) record.
9716	DNS domain was undeleted.
9717	The directory service is unavailable.
9718	DNS zone already exists in the directory service.
9719	DNS server not creating or reading the boot file for the directory service integrated DNS zone.
9751	DNS AXFR (zone transfer) complete.
9752	DNS zone transfer failed.
9753	Added local WINS server.
9801	Secure update call needs to continue update request.
9851	TCP/IP network protocol not installed.
9852	No DNS servers configured for local system.
9901	The specified directory partition does not exist.
9902	The specified directory partition already exists.
9903	The DS is not enlisted in the specified directory partition.
9904	The DS is already enlisted in the specified directory partition.
10004	A blocking operation was interrupted by a call to WSACancelBlockingCall.
10009	The file handle supplied is not valid.
10013	An attempt was made to access a socket in a way forbidden by its access permissions.
10014	The system detected an invalid pointer address in attempting to use a pointer argument in a call.
10022	An invalid argument was supplied.
10024	Too many open sockets.
10035	A non-blocking socket operation could not be completed immediately.
10036	A blocking operation is currently executing.
10037	An operation was attempted on a non-blocking socket that already had an operation in progress.
10038	An operation was attempted on something that is not a socket.
10039	A required address was omitted from an operation on a socket.
10040	A message sent on a datagram socket was larger than the internal message buffer or some other network limit, or the buffer used to receive a datagram into was smaller than the datagram itself.
10041	A protocol was specified in the socket function call that does not support the semantics of the socket type requested.
10042	An unknown, invalid, or unsupported option or level was specified in a getsockopt or setsockopt call.
10043	The requested protocol has not been configured into the system, or no implementation for it exists.
10044	The support for the specified socket type does not exist in this address family.
10045	The attempted operation is not supported for the type of object referenced.
10046	The protocol family has not been configured into the system or no implementation for it exists.
10047	An address incompatible with the requested protocol was used.
10048	Only one usage of each socket address (protocol/network address/port) is normally permitted.
10049	The requested address is not valid in its context.
10050	A socket operation encountered a dead network.
10051	A socket operation was attempted to an unreachable network.
10052	The connection has been broken due to keep-alive activity detecting a failure while the operation was in progress.
10053	An established connection was aborted by the software in your host machine.
10054	An existing connection was forcibly closed by the remote host.
10055	An operation on a socket could not be performed because the system lacked sufficient buffer space or because a queue was full.
10056	A connect request was made on an already connected socket.
10057	A request to send or receive data was disallowed because the socket is not connected and (when sending on a datagram socket using a sendto call) no address was supplied.
10058	A request to send or receive data was disallowed because the socket had already been shut down in that direction with a previous shutdown call.
10059	Too many references to some kernel object.
10060	A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond.
10061	No connection could be made because the target machine actively refused it.
10062	Cannot translate name.
10063	Name component or name was too long.
10064	A socket operation failed because the destination host was down.
10065	A socket operation was attempted to an unreachable host.
10066	Cannot remove a directory that is not empty.
10067	A Windows Sockets implementation may have a limit on the number of applications that may use it simultaneously.
10068	Ran out of quota.
10069	Ran out of disk quota.
10070	File handle reference is no longer available.
10071	Item is not available locally.
10091	WSAStartup cannot function at this time because the underlying system it uses to provide network services is currently unavailable.
10092	The Windows Sockets version requested is not supported.
10093	Either the application has not called WSAStartup, or WSAStartup failed.
10101	Returned by WSARecv or WSARecvFrom to indicate the remote party has initiated a graceful shutdown sequence.
10102	No more results can be returned by WSALookupServiceNext.
10103	A call to WSALookupServiceEnd was made while this call was still processing. The call has been canceled.
10104	The procedure call table is invalid.
10105	The requested service provider is invalid.
10106	The requested service provider could not be loaded or initialized.
10107	A system call that should never fail has failed.
10108	No such service is known. The service cannot be found in the specified name space.
10109	The specified class was not found.
10110	No more results can be returned by WSALookupServiceNext.
10111	A call to WSALookupServiceEnd was made while this call was still processing. The call has been canceled.
10112	A database query failed because it was actively refused.

Visit the Software Design web site to download the latest release of Gregory Braun's Windows error message wizard.

This was last updated in November 2008

Error messages for Windows XP Pro

Dig Deeper on Windows legacy operating systems

NetBIOS (Network Basic Input/Output System)

Don't let RabbitMQ vulnerabilities expose your CI pipelines

How can a local file inclusion attack be stopped?

Stop an Outlook certificate error before serious trouble erupts